User manual KARCHER SE 3001

[. . . ] Do not handle the cleaner or plug with wet hands. Do not use the cleaner if the cord or plug are damaged or if the cleaner has been damaged, dropped or has come into contact with water or any other liquid. Do not use the cleaner to pick up water or any other liquid. Electrical shocks could occur if used outdoors or on wet surfaces. [. . . ] The clear bin alone may be washed out after emptying. Ensure this is completely dry before using the cleaner again. 6. KARCHER CUSTOMER CARE Helpline 01666 827272 T ET B U RY HILL Facsimile 01666 827298 Contact for all service assistance MALMESBURY W I LTS H I R E EN G L AN D S N 16 O R P 00753-01 00746-01 21/11/97 REV 1 1. Getting started Assemble the machine as follows: P L E A S E R E A D A L L I N S T R U C T I O N S C A R E F U L LY BEFORE USING YOUR KARCHER VACUUM CLEANER. Wand & hose assembly Push yellow hose cuff firmly over wand end with twisting motion. Accessory tool location All tools are stored neatly on the tool storage posts. 1 Tool adaptor 1 Guide wand into hose, keeping it straight. 2 Locate wand handle into socket from above. 3 Push home until it `clicks' into place. 2 4 Cord storage Wrap cord around both cable winders. click Rotate top quick-release cable winder. . . Ensure hose does not kink when replacing wand . . . to release cable. 4 Insert tool on to end of wand as shown. 5 For cleaning awkward places remove wand and insert tool adaptor into end of hose. Attach tool as required. Cleaner head adjustment Hold the cleaner head down with foot and tilt machine back. 5 Tool adaptor On/Off switch Cleaner head adjusts automatically to correct height. 2. How to use Clear bin capacity Do not fill above this line. WARNING! For your own safety please remember to unplug the machine when not in use and before carrying out maintenance. Carrying handle Ensure clear bin is firmly in place before lifting. Clear bin removal & emptying 1 Press yellow bin catch to release bin. 2 Remove clear bin and cyclone top from machine by lifting up until it releases. 3 Remove clear bin from cyclone top and wrap a plastic bag around the rim of the clear bin. 4 Invert clear bin and wait at least 10 seconds before releasing. 5 Wipe shroud holes free of all dust and debris. 6 Replace clear bin and cyclone top ensuring that they `click' into upright position. Filter changing 1 Lift out pre-filter. Unhinge filter cage and replace old S-level submicro filter at least every three months. Optional clear bin cleaning Remove clear bin from machine to wash in water if desired. After washing ensure that the yellow bin inner is in place (See step 7 of `Blockage procedure' in your instructions). Do not use strong detergents and ensure clear bin is fully dry before replacing on machine 2 Lift yellow bin catch for access to second S-level submicro filter. Remove any blockage with a stiff wire. 2 3 Remove clear bin and cyclone top, by lifting up until it releases. Then gently pull off from ball socket. 6. Check yellow bin inner Cone seal 4 4 Remove hose from machine by pressing yellow button behind bin cavity. click Check that yellow bin inner is in place, especially if you have washed it. (See `How to use' section in your instructions). Check cone seal is in place: failure to do so could result in clogging of the pre-filter and damage to the motor. The lip of the cone seal should sit over the rim of the yellow bin inner. 6 5 5 Check for any blockages in hose and remove. Cone seal 6 When returning hose, ensure the yellow button `clicks' into place. (A tool may be required to ease re-assembly). KARCHER CUSTOMER CARE If you are still unable to get `suction', call T ET B U RY HILL Dyson Customer Care on 01666 827272. MALMESBURY W I LTS H I R E EN G L AN D S N 16 O R P Important Check both electrostatic filters whenever the bin is emptied and replace at least every 33 months. Please note that if the filters are not checked regularly and changed as required, the motor may overheat, which will cause the thermal cut-out to operate. NOTE: Vacuuming builder's dust and some carpet fresheners may cause the filters to require changing more frequently. (Dyson does not recommend the use of carpet fresheners). Replacement filters are available from your local retailer or direct from Dyson. [. . . ] If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed/safely disposed of. Warning: Under no circumstances should the severed plug be inserted into a 13A socket, serious danger of electric shock would result from the exposed wires. The mains lead can then be shortened to the minimum required length, suitably prepared and the correct style of plug to suit your household wiring system should be fitted. The following wiring instructions should be followed. [. . . ]