User manual KARCHER WPC 600 FW

[. . . ] Ort, Datum, Unterschrift (Kunde) Ort, Datum, Unterschrift (Kärcher-Service) DE -9 11 English Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners. 1 1 2 2 2 2 2 5 5 6 7 7 7 Operating elements 1 2 3 4 5 6 7 8 9 Media filter Active carbon filter Fine filter Manometer for inlet pressure of fine filter Control for media filter Manometer for input pressure for media filter Control active carbon filter Manometer for input pressure of active carbon filter Concentrate regulation valve Control board Operating field Manometer for concentrate pressure Manometre for pump pressure Manometer for output pressure of fine filter Pressure regulation valve Flow meter for drinking water Flow meter for concentrate RO filter unit Display LED "inlet valve active" LED "HP pump active" LED "Maintenance" LED "Chemical dosing active" LED "CD" (conductivity too high) LED "Interruption" Navigation keys ENTER key SET key ON/OFF key QUIT key – – Follow the drinking water regulations. Chemicals Please wear safety gloves and safety goggles while handling acid-resistant chemicals. € Store the chemicals in a cool and dry place and at temperatures above 5°C. [. . . ] Before Commissioning  Check the connection of the plant to the raw water source. σ Ensure uninterrupted flow of the generated drinking water into a tank or a suitable user-side facility. Note The drinking water must be able to flow out without any counter-pressure. The height difference must not be more than 3 m. Advance pressure unit Note If an advance pressure unit is required, then the same would be installed by the Kärcher service technician. EN -2 13 Maintenance schedule Time daily Check / Activity Filling level of dosing container Air bubbles in the dosing pipes Drinking water flow based on the startup value Drinking water guide value based on the startup value Pressure difference between pump and concentrate pressure Target value adequate filling no air bubbles Lowered by less than 10% Increase within 10% maximum 15% above startup difference In case of deviation refill Bleed dosing pump. Fine regulation Fine regulation Kärcher Customer Service Kärcher Customer Service Replace fine filter Kärcher Customer Service Counter/meter for media and active carbon filters Reflushing has taken place in the last 24 hours Pressure difference fine filter Visual inspection of the plant weekly monthly Fill up operations log Clean and rinse dosing container Visual inspection of raw water pump Float switch in drinking water tank No damage/ leaks can be detected no functional disruption can be detected maximum 0;. 08 MPa no leaks Kärcher Customer Service Kärcher Customer Service Maintenance Works Check media and active carbon filters  Accept the interruption message on the operating panel by pressing the Return key; the unit will start. Replace fine filter Check the pressure difference between the two manometers. 08 MPa, then change the filter inlay: 1 2 3 1 2 Display ADVANCE key Dosing frequency button Screw connections Dosing pump ADVANCE Display – 5s short short – current time Regeneration time Number of regenerations Days and hours since the last regeneration current time Bleed dosing pump. The dosing pump must be dearated if the pump has sucked in air (for e. If the dosing container has been completely emptied). € The unit will stop; the display shows the interruption "Motor protection". σ Read and note the dosing frequency that has been set at the LEDs of the dosing pump. σ Set the dosing frequency to 100% by repeatedly pressing the dosing frequency button and waiting until there are no more bubbles in the suction pipe. σ Set the dosing pump to the original dosing frequency. 1 2 3 4 5 Manometer Filter inlay Seal Filter pot Filter key 1 Return key  Switch off the plant using the "ON/OFF" key. σ Briefly switch on the unit by pressing the "ON/OFF" key until the pressure in the initial filter reduces. σ Switch off the plant using the "ON/OFF" key. σ Insert the filter key at the filter pot and unscrew the filter pot. σ Remove the filter inlay from the filter pot und insert a new filter inlay in the filter pot.  Check sealing ring for damage and replace if required. [. . . ] σ Rectify other faults according to the deNote  If the plant does not start automatically, tails provided in the following tables. If there is an interruption, the plant gets pull the plug out of the socket, wait for 5 switched off automatically and the drinking LED Display Possible cause Remedy glows MainteMaintance spools have been triggered manually. Nance Guide value of drinking water is too high. check raw water supply: Fault Water shortage Low water press. [. . . ]