User manual KAWAI C600

[. . . ] The example instructs the user to remove the power cord plug from the AC outlet. Read all the instructions before using the product. WARNING - When using electric products, basic precautions should always be followed, including the following. WARNING The product should be connected to an AC outlet of the specified voltage. Indicates a potential hazard that could result in death or serious injury if the product is handled incorrectly. If you are going to use an AC power cord, make sure that its has the correct plug shape and conforms to the specified power voltage. Doing so may cause electric shock. Do not insert or disconnect the power cord plug with wet hands. [. . . ] The following parameters are provided: CUTOFF, ATTACK, DECAY and RELEASE. Make sure that the TONE MODIFY button in the CONTROL KNOBS section is lit. If the TONE MODIFY button is turned off, press it to turn it ON. The CONTROL KNOBS are now active and assigned to the Tone Modify parameters for the current sound. Use the CONTROL KNOBS to change the current settings for the selected zone. Each parameter of the TONE MODIFY function has an adjustable range from -50 to +50. 29 CUTOFF: ATTACK: DECAY: RELEASE: Raising the CUTOFF level makes the sound brighter, lowering the level makes the sound duller. As the value increases, the attack time becomes longer, which means a slower attack is produced. This parameter controls the amount of time from the peak level to the sustain level of the sound. This parameter controls the amount of time needed for the sound to fade out after the key is released. Note: If the selected zone is set to BOTH, changing the TONE MODIFY parameters affects both internal and external sections. If you want different settings for internal and external sections, enter the edit mode by pressing the MENU button and select internal or external section with the ZONE SELECT button. (See page33 for details. ) 5. 4 MIDI CC# (Control Change) The C600 can send any MIDI Continuous Controller information to any MIDI Instrument or Device. Use the MENU buttons to scroll through all the different parameters. In SOUND mode, both the Int Zone parameters and the Common parameters without the inverse "S(Setup)" icon can be individually stored. (See page43) The Int Zone parameters can be stored as a SOUND of the C600's 256 SOUNDs. The Common parameters can be stored as the initial settings in SOUND mode. Zone parameters (Int) Mode Sound Selection Damper Reso. (Int Piano only) KeyOff Effect (IntPiano only) Voicing (Int Piano only) Key Range Hi/Lo Velocity Switch On/Off Velocity Switch Value Velocity Compression Velocity Offset Zone Transpose Volume Pan Fine Tune Damper Pedal On/Off/Hold Footswitch On/Off Expression Pedal On/Off Modulation On/Off Bender On/Off Bender Range Solo On/Off Solo Mode Zone parameters (Ext) Common parameters Mode TX Channel TX PRG # On/Off PRG # TX Bank On/Off Bank Select MSB LSB Keyboard On/Off Key Range Hi/Lo Velocity Switch On/Off Velocity Switch Value Velocity Compression Velocity Offset Zone Transpose TX Volume On/Off Volume TX Controller On/Off Pan Fine Tune Damper Pedal On/Off Footswitch On/Off Expression Pedal On/Off Modulation On/Off Bender On/Off TX Bender Range On/Off Bender Range Solo On/Off Solo Mode Master Volume Left Pedal Mode M. Wheel CC# Expression Pedal CC# Footswitch CC# Temperament Stretch Tuning Caution: The edited settings will be erased when the power is turned off, or other sound is recalled. To save these settings, use the STORE procedure to save them as a SETUP. (See page43) 32 6. 1 Editing Procedure and Parameters First, press the ZONE SELECT button for the zone to be edited. Next, press the MENU buttons until the parameter you want to edit appears in the DISPLAY. When a zone is set as Both, pressing the ZONE SELECT button again will switch the menu list from Internal to External or vice versa. Set the value of the parameter using the VALUE buttons. Since each parameter has a different value range, consult the following pages for the details. [. . . ] The USB logo can be used only for the product which is approved by USB-IF (USB Implements Forum Inc. ) test. * Windows is registered trademark of Microsoft Corporation. * Macintosh is registered trademark of Apple Computer, Inc. 60 Specifications Keyboard # of Zone # of Internal Sound Polyphony Effect 88 Wooden keys with AWA Grand PRO II 4 zones 256 sounds Maximum 192 7 Reverbs 22 Effects 4-band Equalizer 256 SETUPs 16 x 2 LCD w/backlight 1/4" Out (L/MONO, R) XLR Out (L, R) with Ground Lift Switch [1pin-GND/2pin-hot/3pin-cold] Headphones MIDI IN/OUT/THRU USB (to Host) Damper/Soft Foot Controller EXP (Assignable) FSW (Assignable) AC Inlet Power Consumption 15W Internal Memory Display Jack Dimensions (WxDxH) 1466 x 442 x 189 mm (57 3/4" x 17 1/2" x 7 1/2") Weight 35kg(77 lbs) Accessories included Damper/Soft Pedal [F-20] Music Rack Power Cable Owner's Manual * Specifications subject to change without notice. 61 C600 MIDI Implementation Contents 1. Recognized data 1. 1 Channel Voice Message 1. 2 Channel Mode Message 1. 3 System Real time Message 2. [. . . ]