User manual KAWAI CA330

[. . . ] The example instructs the user to remove the power cord plug from the AC outlet. Read all the instructions before using the product. WARNING - When using electric products, basic precautions should always be followed, including the following. WARNING The product should be connected to an AC outlet of the specified voltage. Indicates a potential hazard that could result in death or serious injury if the product is handled incorrectly. If you are going to use an AC power cord, make sure that its has the correct plug shape and conforms to the specified power voltage. Doing so may cause electric shock. Do not insert or disconnect the power cord plug with wet hands. [. . . ] The CONTROL KNOBS are now active and assigned to the Tone Modify parameters for the current sound. Use the CONTROL KNOBS to change the current settings for the selected zone. Each parameter of the TONE MODIFY function has an adjustable range from -50 to +50. 29 CUTOFF: ATTACK: DECAY: RELEASE: Raising the CUTOFF level makes the sound brighter, lowering the level makes the sound duller. As the value increases, the attack time becomes longer, which means a slower attack is produced. This parameter controls the amount of time from the peak level to the sustain level of the sound. This parameter controls the amount of time needed for the sound to fade out after the key is released. Note: If the selected zone is set to BOTH, changing the TONE MODIFY parameters affects both internal and external sections. If you want different settings for internal and external sections, enter the edit mode by pressing the MENU button and select internal or external section with the ZONE SELECT button. (See page33 for details. ) 5. 4 MIDI CC# (Control Change) The CA330 can send any MIDI Continuous Controller information to any MIDI Instrument or Device. This powerful feature allows for editing the sounds of an external sound module in Real Time during performance, or for recording Real Time performance edits to a MIDI sequencer. Some control changes are also effective to internal sounds. Make sure that the MIDI CC# button in the CONTROL KNOBS section is lit. The Common parameters can be stored as the initial settings in SOUND mode. Zone parameters (Int) Mode Sound Selection Damper Reso. (Int Piano only) KeyOff Effect (Int Piano only) Voicing (Int Piano only) Key Range Hi/Lo Velocity Switch On/Off Velocity Switch Value Velocity Compression Velocity Offset Zone Transpose Volume Pan Fine Tune Damper Pedal On/Off/Hold Footswitch On/Off Expression Pedal On/Off Modulation On/Off Bender On/Off Bender Range Solo On/Off Solo Mode Zone parameters (Ext) Common parameters Mode TX Channel TX PRG # On/Off PRG # TX Bank On/Off Bank Select MSB LSB Keyboard On/Off Key Range Hi/Lo Velocity Switch On/Off Velocity Switch Value Velocity Compression Velocity Offset Zone Transpose TX Volume On/Off Volume TX Controller On/Off Pan Fine Tune Damper Pedal On/Off Footswitch On/Off Expression Pedal On/Off Modulation On/Off Bender On/Off TX Bender Range On/Off Bender Range Solo On/Off Solo Mode Master Volume Left Pedal Mode M. Wheel CC# Expression Pedal CC# Footswitch CC# Temperament Stretch Tuning Caution: The edited settings will be erased when the power is turned off, or other sound is recalled. To save these settings, use the STORE procedure to save them as a SETUP. (see page43) 32 6. 1 Editing Procedure and Parameters First, press the ZONE SELECT button for the zone to be edited. Next, press the MENU buttons until the parameter you want to edit appears in the DISPLAY. When a zone is set as Both, pressing the ZONE SELECT button again will switch the menu list from Internal to External or vice versa. Set the value of the parameter using the VALUE buttons. Since each parameter has a different value range, consult the following pages for the details. Repeat this procedure for any other parameters in any of the zones that need to be modified. Save these settings using the STORE button. (See page43 for detail) Note: Once you enter the edit mode from SETUP mode by pressing the MENU button, the mode automatically changes to SOUND mode and the SOUND SELECT buttons are used to select sounds, not SETUPs. [. . . ] The USB logo can be used only for the product which is approved by USB-IF (USB Implements Forum Inc. ) test. * Windows is registered trademark of Microsoft Corporation. * Macintosh is registered trademark of Apple Computer, Inc. 60 Specifications Keyboard # of Zone # of Internal Sound Polyphony Effect 88 keys with Advanced Hammer Action IV 4 zones 256 sounds Maximum 192 7 Reverbs 22 Effects 4-band Equalizer 256 SETUPs 16 x 2 LCD w/backlight 1/4" Out (L/MONO, R) Headphones MIDI IN/OUT/THRU USB (to Host) Foot Controller Damper EXP (Assignable) Foot Switch (Assignable) AC Inlet 15W Internal Memory Display Jack Power Consumption Dimensions (WxDxH) 1356 x 340 x 172 mm (53 3/8" x 13 3/8" x 6 7/8") Weight 20. 5kg(45 lbs) Accessories included Damper Pedal [F-10H] Music Rack Power Cable Owner's Manual * Specifications subject to change without notice. 61 CA330 MIDI Implementation Contents 1. Recognized data 1. 1 Channel Voice Message 1. 2 Channel Mode Message 1. 3 System Real time Message 2. [. . . ]