User manual KAWAI CA770

[. . . ] Stepping on or tripping over it can break or short-circuit the wire inside. The product should be connected to a power supply only of the type described in the operatiing instructions or as marked on the product. Pulling the AC power cord itself may damage the cord, causing a fire, electric shock or short-circuit. When disconnecting the AC power cord's plug, always hold the plug and pull it to remove it. 120V 230V 240V Do not attempt to service the product beyond that described in the user-maintenance instructions. All other servicing should be reffered to qualified service personnel. III This product in combination with an amplifier and headphones or speakers, may be capable or producing sound level that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a level that is uncomfortable. [. . . ] Notes within these borders will not be quantized and notes outside the borders will be moved to the nearest beat specified by the resolution value (Quarter note, Eighth note, etc. ). The negative value represents the placement of the "border" before the beat, and the positive value represents the placement the "border" after the beat. Together, these two "borders" form a timing "range" around the specified beat. Resolution 24 Beat 12 Beat 12 Range 0, 0 « » » « Selecting zero Range results in no "range", and all notes are shifted to the precise beat. « « Resolution 24 Beat 12 Beat 12 Range -3, 3 « The notes that fall beyond the Range are moved to the closest "border" of the Range. » Resolution 48 Beat 24 Beat 24 The notes that fall inside the Range are not shifted at all. Range 2, 10 « » By experimenting with Resolution and Range settings, you can correct the timing of the notes in your recording while still allowing for a natural, human feel. 60 Kawai Concert Performer Series Digital Piano Copy The Copy function allows you to copy a section or all of the data on a track to another location. The destination may be on the same track, or it can be on another track. · The destination of the copied data must either be: 1) A location that already has data in it. 2) The first blank bar after the end of a track (Bar 1 if the destination track is empty). For example, if a track only has 10 bars in it, you cannot copy data onto bar 20. You can, however, copy data to bars 1 through 11. · Copied data replaces any current data that may be at the destination. L1 R1 L2 Selects the track to be copied. Use the Dial to select the track numbers 1-16, Tempo, or Chord. Use the Dial to change the value. R3 L5 R5 F1 F2 F3 F4 F5 F6 F7 F1 F2 F7 Takes you to the previous menu. 64 Kawai Concert Performer Series Digital Piano Erase Erases data in the bars that you specify, and leaves them as empty bars. L1 R1 R2 L2 Selects the track that has the bars you want to erase. Use the Dial to change the bar. L2 L3 L3 L4 R3 R4 L4 L5 R5 F1 F2 F3 F4 F5 F6 F7 F1 F2 F7 Takes you to the Advanced Recorder menu. Proceeds with the Erase. Recording a Song P. 65 Merge Merge combines data from two tracks. You can make complex musical phrases using several tracks, then combine them together on one track. Remember that there can only be one instrument sound assigned to each track, so the resulting merged track will play all the combined data using one instrument sound. Merge can be useful for making rhythm patterns by first recording different drum/ percussion parts using the same drum kit on several tracks for easy editing of each instrument, or recording the right and left hand parts of a piano piece and combining them later on one track to free up extra tracks for more recording. · Merge does not automatically erase the track from where you copied the data. L1 R1 R2 L2 Selects the track from where you want to copy data. Choose 1-16. L2 R2 Select the track where you want this data merged to. Choose 1-16. L3 L4 R3 R4 L5 R5 F1 F2 F3 F4 F5 F6 F7 F1 F2 F7 Takes you to the Advanced Recorder menu. [. . . ] The CP can be connected directly to the back of your computer via a USB cable. In order for the CP and your computer to properly communicate over this USB cable, you first need to set the MIDI-USB switch located next to the MIDI jacks to USB. Also your computer must have a USB driver installed. Please read the instruction on the next page for the details about the USB driver. Appendice P. [. . . ]