User manual KAWAI EP308

[. . . ] denotes an operation that should be carried out. The example instructs the user to remove the power cord plug from the AC outlet. Read all the instructions before using the product. WARNING - When using electric products, basic precautions should always be followed, including the following. potential could result in death WARNING Indicates ainjury if thehazard thathandled incorrectly. or serious product is The product should be connected to an AC outlet of the specified voltage. 120V 230V 240V G If you are going to use an AC power cord, make sure that its has the correct plug shape and conforms to the specified power voltage. [. . . ] EFX rate and REVERB time are effective to internal zone only. EFX type, EFX rate and EFX depth are common to all internal zones. If the selected zone is set to BOTH, changing the value for EFX depth or REVERB depth affects for both internal and external sections. If you want different settings for internal and external sections, first enter the edit mode by pressing the MENU button and press the EFFECT button. Now you can select internal or external zone with ZONE SELECT button. (See page 29 for details. ) 5. 2 EQ (EQUALIZER) The EP308 contains a four-band graphic equalizer to shape the overall tone of the sound. The EQ affects all zones at the same time. However, each SETUP can have its own EQ setting that affects the internal sounds only. Be sure that the EQ button in the CONTROL KNOBS section is lit. If the EQ button is turned off, press it to turn it ON. The CONTROL KNOBS are now active and assigned to the EQ parameters. When the selected zone is set to INT or BOTH, the display shows the parameter names. 1PAN STN VbR VbD 0 0 0 0 When the selected zone is set to EXT, the display shows the MIDI CC numbers. 3010 070 076 077 64 64 64 64 The default parameters assigned for each knob are as follows. A: #10 Panpot (PAN) B: #70 Sustain Level (STN) C: #76 Vibrato Rate (VbR) D: #77 Vibrato Depth (VbD) Note: If the selected zone is set to BOTH, changing the MIDI CC# parameters affects for both internal and external sections. If you want different settings for internal and external sections, enter the edit mode by pressing the MENU button and select internal or external section with ZONE SELECT button. (See page 29 for details. ) Changing MIDI CC parameter Press and hold the MIDI CC# button. The MIDI CC# button starts blinking and the cursor in the display moves up to the parameter name. 1PAN STN VbR VbD 0 0 0 0 Use the CONTROL KNOBS to change the parameters. After changing the parameter, press the MIDI CC# button again. The MIDI CC# button stops blinking and the cursor in the display moves down to the value. 26 Note: When the selected zone is set to INT, only the following parameters can be selected. 10 11 70 71 76 77 78 93 Panpot Expression Sustain Level Resonance Vibrato Rate Vibrato Depth Vibrato Delay Chorus Depth PAN EXP STN RSN VbR VbD VbY ChD When the selected zone is set to BOTH and the internal section is selected in edit mode, the parameters not available for INT section show as XXX. 1015 STN VbR VbD Ixxx 0 0 0 27 6. MENU The MENU buttons allow access to the edit parameters in the EP308. This collection of settings together with other editable parameters can be stored as a SETUP. The EP308 provides 64 SETUPs, and all are user programmable. Each zone can be set as Internal, External or Both individually. [. . . ] [For Macintosh users] Macintosh OSX automatically recognizes our USB interface. Older Macintosh OS are not supported by us. If you have an older Macintosh OS, please use an appropriate MIDI interface and MIDI cables when connecting the EP308 to a Macintosh computer. NOTE: When both MIDI jacks and USB jack are connected, USB has priority. [. . . ]