User manual KAWAI FS750

[. . . ] Before use, perform an advance check as described in this manual. Introduction Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from improper use of this product. Please read the following items before use This Case is a precision device designed for use at a water depth within 40 m. Please use the Case correctly after sufficient understanding of the contents of this manual in regard to handling of the Case, checks before use, maintenance, and storage after use. [. . . ] When it is difficult, water leakage can be checked by referring "Water Leakage Test" (P. 19). 2 Main causes of water leakage are as follows. · Forgetting to install the O-ring · Part of an O-ring or an entire O-ring is outside the specified groove. · O-ring damage, cracks, deterioration or deformation · Sand, fibers, hair or other foreign matter sticking to the O-ring, the O-ring groove or the O-ring contact surface. · Damage to an O-ring groove or O-ring contact surface. · Attached strap or silica gel getting caught when closing the Case. Perform the test after the above causes have been eliminated. CAUTION: If the advance test should show water leakage with normal handling, stop using the Case and contact your dealer or an Olympus service station. En EN 10 3. How to connect the electronic flash Connecting the underwater optical fiber cable To connect the UFL-2 underwater flash (optional) to the Case using an underwater optical fiber cable (optional), follow the procedures below. How to connect the underwater optical fiber cable 1 Remove the cap of the optical fiber cable insertion slot. 2 Put the underwater optical fiber cable plug all the way into the optical fiber cable insertion slot. Setting of the digital camera 1 Set the RC mode of the camera to ON so that the camera's built-in flash is activated. 2 Load the camera in the Case with the camera's built-in flash popped up. Refer to the UFL-2 instruction manual for the UFL-2 operation. Remove the eyecup from the digital camera. To improve the view of the pickup viewfinder, remove the camera's eyecup before loading it in the Case. The eyecup removed from the camera can be stored in the camera table. CAUTION: In case the digital camera is loaded in the Case without removing the eyecup and the rear lid of the Case is closed, the pickup viewfinder pops out. Remove the eyecup, then push in the pickup viewfinder. En 5. Remove the filter from the digital camera The digital camera cannot be loaded in the Case while the filter is attached to the lens. EN 14 Open the Case 1 Slide and hold the slide lock towards the arrow direction (1) and turn the open/close dial counter clockwise (2). 2 Turn the open/close dial to the position where it cannot be turned further. 3 Open the rear lid of the Case gently. Slide lock 1 2 CAUTION: Do not exert too much force while turning the open/close dial. Doing so may damage the dial. Attach the digital camera to the camera table In order to load the camera into the Case, attach the camera table (located on the front-lid side of the Case) to the digital camera. 1 The eyecup and the hot shoe cover of the digital camera can be stored in the camera table. 2 Attach the camera table to the tripod seat section on the bottom of the digital camera. Use the camera's tripod screw hole for attaching. En 3 The camera table has fixed up-down and front-rear orientations. To ensure that it is properly attached, refer to the illustration on the right. Up Front Down Rear EN 15 Insert the digital camera in the Case 1 Pull out the zoom dial and mode dial on the Case (pulling out the mode dial also pulls up the power switch lever) so that they do not get in the way while loading the digital camera. At this time, set the orientation of the power switch lever as shown below. 2 After attaching the camera table to the digital camera, slide the camera table into the Case's camera table-loading groove. [. . . ] · Do not try to replace the O-ring by yourself. · We recommend to perform the check periodically. Maintenance of the threaded sections on the TTL cable and TTL cable connector If the threaded sections used to connect the TTL cable to the TTL cable connector are not maintained properly, salt and other seawater residue may adhere to the TTL cable and prevent it from being disconnected. After use in seawater, clean off any salt, sand, or other residue as soon as possible, then dry the equipment thoroughly. Clean the threaded sections with a cotton swab and apply a thin, uniform layer of silicone grease (provided with this case). Clean and apply silicone grease to these sections. Maintenance of the TTL Connector Cap After removing the TTL connector cap from the Underwater Case, be sure to clean and grease the Oring. [. . . ]