User manual KAWAI FS780

[. . . ] Before use, perform an advance check as described in this manual. Introduction Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from improper use of this product. shall not be responsible for damage, lost profits, etc. [. . . ] For details, see "How to attach the camera table to the digital camera" (P. CAUTION: In case the digital camera is loaded in the Case without removing the eyecup and the rear lid of the Case is closed, the pickup viewfinder pops out. Remove the eyecup, then push in the pickup viewfinder. En EN 16 Remove the filter from the digital camera If a filter is attached to the lens of the digital camera, remove the filter before loading the digital camera in the Case. CAUTION: The digital camera cannot be loaded in the Case while the filter is attached to the lens. Be sure to remove the filter before loading. Prepare the digital camera Compatible digital camera This product (FS780) is exclusively for use with the E-520 Digital Camera. Checking camera operation Refer to the digital camera's instruction manual for details on how to make sure the camera is operating correctly. Open the Case 1 Slide and hold the slide lock towards the arrow direction (1) and turn the open/close dial counter clockwise (2). 2 Turn the open/close dial to the position where it cannot be turned further. 3 Open the rear lid of the Case gently. Slide lock 1 2 En CAUTION: Do not exert too much force while turning the open/close dial. Doing so may damage the dial. EN 17 Attach the zoom and focus gears provided with the optional underwater port to the lens. To control the zooming and manual focusing of the camera's lens, attach the zoom gear and focus gear (provided with the optional underwater port) to the lens' zoom ring and focus ring. Refer to the optional underwater port's instruction manual for more details on how to attach the gears. [Example 1] Attaching the 14-42 mm zoom gear provided with the PPO-E05 to the lens For details, refer to the instruction manual for the PPO-E05. [Example 2] Attaching the optional underwater zoom/focus gears (PPZR-E03/E04/E05) to the lens For details, refer to the instruction manual for the zoom/focus gears. [Example 3] Attaching the provided zoom/focus gears to the PPO-E01/E02/E03 Lock lever En Zoom/focus gear Use the lock gear to clamp the zoom/focus gear. CAUTION: · Make sure that the zoom gear is clamped firmly by the lock lever. · For details on the correct attachment position of the zoom gear on the lens, refer to the instruction manual provided with the optional underwater lens port. EN 18 How to attach the camera table to the digital camera In order to load the camera into the Case, attach the camera table (located on the front-lid side of the Case) to the digital camera. · The strap, lens cap and filter are removed from the digital camera. · The camera table provided with the Case is attached to the tripod screw hole at the bottom of the digital camera. · The camera's eyecup is removed from the camera's viewfinder. · The zoom gear and focus gear are attached to the camera's lens. 1 Pull out the zoom dial and mode dial on the Case (pulling out the mode dial also pulls up the power switch lever) so that they do not get in the way while loading the digital camera. At this time, set the orientation of the power switch lever as shown below. En 2 When using an electronic flash with a TTL cable, remove the TTL cable connector cap on the hot shoe connector, which is located in the top left corner of the inner side of the front lid. and connect the TTL cable to the connector. Remove the cap by turning it counterclockwise. CAUTION: When screwing in the hot shoe connector clamping screw, place the Case upside down. Be careful not to drop the Case. EN 21 3 When using a slave flash from a non-Olympus manufacturer, push the # button on the camera to pop up its built-in flash. # button CAUTION: The built-in flash should be popped up before loading the camera in the Case. Once the case has been sealed, the built-in flash cannot be popped up from outside the Case. To pop up the flash after the case has been sealed, change the camera's automatic pop-up setting to ON, set the camera to a scene mode other than AUTO and underwater modes, point the camera at the subject and half-press the shutter button so that the built-in flash pops up automatically. 4 After attaching the camera table to the digital camera, slide the camera table into the Case's camera table-loading groove. Do not insert the camera table by force. Slide it in gently while checking that the digital camera does not interfere with the internal parts of the Case. En EN 22 5 When using an external electronic flash with a TTL cable, connect the hot shoe cable to the camera's hot shoe and set the camera's automatic pop-up setting to OFF. CAUTION: After confirming the camera's automatic pop-up setting, be sure to switch the camera OFF. 6 Gently push the Case's zoom dial and mode dial down and confirm that the zoom dial can smoothly control zooming, the power switch lever can turn the digital camera ON/OFF, and that the mode dial can control the mode dial of the camera. CAUTION: · Before loading the digital camera, attach the zoom and focus gears to the Case's zoom and focus rings. [. . . ] O-rings for other Case models cannot be used. 2 The following waterproof ports are available for use with the FS780 Choose the one corresponding to the lens you are using. EN 37 Waterproof Port Withstanding depth Applicable Lens 14-45 mm Note Packaged with the PPZR-E01 underwater zoom gear for 14-45 mm lens. The provided PPZR-E01 zoom gear cannot be used. The focus ring rotation angle can be increased to 360° by using the optional PPZRE04 underwater focus gear. [. . . ]