User manual KAWAI K 1 RII

[. . . ] · Injury caused by the swallowing of small parts. Please consult a doctor immediately if this happens. If it is broken or smashed by being dropped or hit against a hard object, glass splinters could cause injury. If water gets into this product during underwater use, immediately stop using it, remove the moisture from the product and detach it from the camera and lens. [. . . ] If water gets into this product during underwater use, immediately stop using it, remove the moisture from the product and detach it from the camera and lens. Do not disassemble or modify this product. The silicone O-ring grease is not edible. CAUTION Do not expose this product to high temperatures for extended periods. This may lead to deterioration of the product's components. When mounting this product on the PT-E series waterproof case, be sure to follow the steps described in this manual. Before detaching this product from the PT-E series waterproof case, make sure that the case is completely dry and free of moisture. Never attach or detach this product in locations where there is a lot of sand, dust or dirt. If any foreign matter gets on the O-ring sections, the waterproof sealing will be compromised and water leakage may result. This product has been designed and manufactured for use in a water pressure equivalent to a depth of 60 meters (200 ft). Please note that diving in depths over 60 meters may cause irreparable damage and/or may result in water leaking into this product and the camera and lens. If a lens cap or filter is attached to the lens or the strap is attached to the camera, remove them as well. Power switch dial Mode dial knob Zoom/MF dial Pull out the zoom/MF dial further. MENU Camera table lock lever Pull up the power switch dial, mode dial knob and zoom/MF dial on the PT-E series case, and turn the case's camera table lock lever counterclockwise to release the lock. Attach the flash hot shoe cable as instructed in the PT-E series case manual. Confirm that the camera's power switch is OFF. While pulling out the zoom/MF dial on the PT-E series case , slide the camera table with camera attached as far as it will go into the camera table mount on the inner side of the case's front lid. E-5 MENU After inserting the camera, turn the PT-E series case's camera table lock lever all the way clockwise to lock the camera table. Then, push in the zoom/MF dial on the PT-E series case and engage it with the gear attached to the lens. Turn the zoom/MF dial to confirm that it can control the lens's MF operation. Push in the PT-E series case's power switch dial and mode dial knob. Turn the power switch dial and mode dial knob and confirm that they can control the camera power ON-OFF and mode switching. Connect the hot shoe mount section of the hot shoe cable that has been connected to the PT-E series case to the hot shoe of the camera. Attach the rear lid of the PT-E series case and lock the four buckles (two diagonally located buckles first, and then the other two diagonally located buckles). Underwater shooting is now possible. E-6 6 Maintenance For safe use of this product, always perform maintenance after each diving session. For details, refer to "Handling After Shooting" and "Maintaining the Waterproof Function" in the PT-E series case instruction manual. Apply the same procedures to this product. After shooting, remove the inserted camera and lens, then re-seal the empty case and immerse it in tap water to remove any salt as soon as possible. After making sure that the PT-E series case is completely dry, dismount this product from the case. Remove the O-rings from this product using the provided pick for removing O-rings. [. . . ] Underwater shooting is now possible. E-6 6 Maintenance For safe use of this product, always perform maintenance after each diving session. For details, refer to "Handling After Shooting" and "Maintaining the Waterproof Function" in the PT-E series case instruction manual. Apply the same procedures to this product. After shooting, remove the inserted camera and lens, then re-seal the empty case and immerse it in tap water to remove any salt as soon as possible. After making sure that the PT-E series case is completely dry, dismount this product from the case. Remove the O-rings from this product using the provided pick for removing O-rings. Take care not to damage the O-rings. Remove sand and dust from the O-rings. [. . . ]