Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual KAWASAKI Z750. We hope that this KAWASAKI Z750 user guide will be useful to you.
Lastmanuals help download the user guide KAWASAKI Z750.
Detailed instructions for use are in the User's Guide.
[. . . ] Z750 Z750 ABS
Motorcycle Service Manual
Quick Reference Guide
General Information Periodic Maintenance Fuel System (DFI) Cooling System Engine Top End Clutch Engine Lubrication System Engine Removal/Installation Crankshaft/Transmission Wheels/Tires Final Drive Brakes Suspension Steering Frame Electrical System
This quick reference guide will assist you in locating a desired topic or procedure. ·Bend the pages back to match the black tab of the desired chapter number with the black tab on the edge at each table of contents page. ·Refer to the sectional table of contents for the exact pages to locate the specific topic required.
1j
2j
3j
4j
5j
6j
7j
8j
9j
10 j
11 j
12 j
13 j
14 j
15 j
16 j
Appendix
17 j
Z750 Z750 ABS
Motorcycle Service Manual
All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic mechanical photocopying, recording or otherwise, without the prior written permission of Quality Assurance Division/Consumer Products & Machinery Company/Kawasaki Heavy Industries, Ltd. , Japan. [. . . ] ; Install the new circlip [F] into the groove of the oil pump · drive gear shaft.
Special Tool - Outside Circlip Pliers: 57001-144
7-12 ENGINE LUBRICATION SYSTEM
Oil Pressure Measurement
Oil Pressure Measurement
oil passage · Remove the[B] to the plugplug, and attach the adapter [A] and gauge hole.
Special Tools - Oil Pressure Gauge, 10 kgf/cm²: 57001-164 Oil Pressure Gauge Adapter, PT3/8: 57001 -1233
the engine and warm up the engine. · Start the engine at the specified speed, and read the oil Run · pressure gauge. If the oil pressure is much lower than the standard, check the oil pump, relief valve, and/or crankshaft bearing insert wear immediately. If the reading is much higher than the standard, check the oil passages for clogging.
Oil Pressure Standard: 147 226 kPa (1. 5 2. 3 kgf/cm², 21 33 psi) at 4 000 r/min (rpm), oil temperature 90°C (194°F)
engine. · Stop the the oil pressure gauge and adapter. Remove ·
WARNING
Take care against burns form hot engine oil that will drain through the oil passage when the gauge adapter is removed. a non-permanent · Applyand install it. locking agent to the oil passage plug,
Torque - Oil Passage Plugs: 20 N·m (2. 0 kgf·m, 15 ft·lb)
ENGINE LUBRICATION SYSTEM 7-13
Oil Pressure Switch
Oil Pressure Switch Removal
Maintenance chapter) Switch Cover [A] Switch Terminal Bolt [B] Oil Pressure Switch [C]
· Remove:Oil (Drain, see Engine Oil Change in the Periodic Engine
Oil Pressure Switch Installation
· Apply silicone sealant to the threads of the oil pressure switch and tighten it.
Sealant - Kawasaki Bond (Silicone Sealant): 56019-120
the switch lead direction · Install high-temperature grease upward. ·
Torque - Oil Pressure Switch: 15 N·m (1. 5 kgf·m, 11 ft·lb)
Torque - Oil Pressure Switch Terminal Bolt: 2. 0 N·m (0. 20 kgf·m, 18 in·lb)
ENGINE REMOVAL/INSTALLATION 8-1
Engine Removal/Installation
Table of Contents
Exploded View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine Removal/Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 8-4 8-5 8-5 8-7
8
8-2 ENGINE REMOVAL/INSTALLATION
Exploded View
ENGINE REMOVAL/INSTALLATION 8-3
Exploded View
No. 1 2 3 4 5 6 7 8 9 Fastener Adjusting Collar Lock Bolt Adjusting Collar Locknut Engine Ground Cable Terminal Bolt Front Engine Mounting Bolts Lower Engine Mounting Nut Middle Engine Mounting Nut Rear Engine Bracket Bolts Subframe Bolts Upper Engine Bracket Bolts N·m 34 49 9. 8 44 44 44 25 25 44 Torque kgf·m 3. 5 5. 0 1. 0 4. 5 4. 5 4. 5 2. 5 2. 5 4. 5 ft·lb 25 36 87 in·lb 32 32 32 18 18 32 Remarks S S S S S S S S
S: Follow the specified tightening sequence.
8-4 ENGINE REMOVAL/INSTALLATION
Special Tool
Engine Mount Nut Wrench: 57001-1450
ENGINE REMOVAL/INSTALLATION 8-5
Engine Removal/Installation
Engine Removal
of the swingarm with a stand. · Support the rear partlever slowly and hold it with a band Squeeze the brake · [A].
WARNING
Be sure to hold the front brake when removing the engine, or the motorcycle may fall over. It could cause an accident and injury.
CAUTION
Be sure to hold the front brake when removing the engine, or the motorcycle may fall over. The engine or the motorcycle could be damaged.
· Remove:Oil (Drain, see Engine Oil Change in the Periodic Engine
Maintenance chapter) Coolant (Drain, see Coolant Change in the Periodic Maintenance chapter) Center Fairings (see Center Fairing Removal in the Frame chapter) Side Covers (see Side Cover Removal in the Frame chapter) Frame Covers (see Frame Cover Removal in the Frame chapter) Fuel Tank (see Fuel Tank Removal in the Fuel System (DFI) chapter) Clutch Cable Lower End (see Clutch Cable Removal in the Clutch chapter) Thermostat Housing (see Thermostat Removal in the Cooling System chapter) Radiator (see Radiator and Radiator Fan Removal in the Cooling System chapter) Air Switching Valve (see Air Switching Valve Removal in the Engine Top End chapter) Throttle Body Assy (see Throttle Body Assy Removal in the Fuel System (DFI) chapter) Shift Lever (see Shift Pedal Removal in the Crankshaft/Transmission chapter)
· Remove: [A] Quick Rivets
Exhaust Pipe (see Exhaust Pipe Removal in the Engine Top End chapter)
8-6 ENGINE REMOVAL/INSTALLATION
Engine Removal/Installation
· Disconnect:Harness Connector [A] Stick Coil
Camshaft Position Sensor Lead Connector (see Camshaft Position Sensor Removal in the Electrical System chapter)
· Disconnect: Cable (see Starter Motor Removal in the Starter Motor
Electrical System chapter) Alternator Lead Connector (see Alternator Cover Removal in the Electrical System chapter) Crankshaft Sensor Lead Connector (see Crankshaft Sensor Removal in the Electrical System chapter) Neutral Switch Lead Connector [A] Sidestand Switch Lead Connector [B] Speed Sensor Lead Connector [C] Remove the engine sprocket (see Engine Sprocket Removal in the Final Drive chapter).
·
· Remove: Hose End [A] Breather
Engine Ground Cable Terminal Bolt [B]
engine with a suitable stand [A]. · Support the[B] onto the suitable stand for engine balance. Put a plank
· Remove: Mounting Bolts [A] (Both Sides) Front Engine
Adjusting Collar Lock Bolt Subframe Bolts [B] (Both Sides) Upper Engine Bracket Bolts [C] (Both Sides) Subframes [D] (Both Sides) Middle Engine Mounting Nut [E] and Bolt Lower Engine Mounting Nut [F] and Bolt Rear Engine Bracket Bolts [G] Rear Engine Bracket [H]
ENGINE REMOVAL/INSTALLATION 8-7
Engine Removal/Installation
· Using the nut wrench [A], loosen the locknut [B].
Special Tool - Engine Mount Nut Wrench: 57001-1450
· Using the Hexagon Wrench, turn the adjusting collar [A] counterclockwise to make the gap between the engine
and adjusting collar.
chain · Remove the drivetake out[A] from the output shaft [B]. ·
Engine Installation
engine · Support the onto thewith a suitable stand. Put a plank suitable stand for engine the adjusting collar [A] to the frame. [. . . ] Brake Hose (From Right Front Caliper to Left Front Caliper) 4. Brake Hose (From Rear Master Cylinder to Rear Caliper) 7. Clamp
17-46 APPENDIX
Cable, Wire, and Hose Routing
ABS Equipped Models
APPENDIX 17-47
Cable, Wire, and Hose Routing
1. Brake Hose (From Front Master Cylinder to ABS Hydraulic Unit) 2. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KAWASAKI Z750
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual KAWASAKI Z750 will begin.