User manual KAZ HZ-680C

[. . . ] DO NOT attempt to defeat this safety feature. This heater draws 12. 5 amps during operation when in the high setting. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. [. . . ] 2 IT MAY BE TRIPPED OVER BY CHILDREN OR PETS. · The Tower Surround Heater is designed to disperse heat in either a 360° range or in one direction only. To select the desired heating mode, 360° Heating slide the Direction Control switch, located on the top of the heater, to the position of your choice (Fig. 2): ­ to the left ( ) for 360° Heating ­ to the right ( ) for Forward Only Heating (One Direction Heating) · With the Power knob in the OFF position, plug the heater into a polarized 120V outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET; it will only fit one way. · Turn the Thermostat control fully clockwise to the HIGH setting. · This heater is equipped with three (3) settings: High, Low and Fan Only. The High setting uses 1500 watts of power and the Low setting uses 750 watts of power. You can select the proper setting to accommodate your comfort level. Because the Low setting does not require as much electricity to operate, it is more energy efficient and may be a better option if you are concerned about the amperage draw on a circuit when the heater is in the High setting. · Turn the heater on using the Child Resistant Switch (Power knob). · Push down and turn the Power knob to OFF and unplug the heater when you are finished using it. HZ-3220 OPERATION · The Tower Surround Heater is designed to disperse heat in either a 360° Fig. To select the desired heating mode, slide the Direction Control switch, located on the top of the heater, to the position of your choice (Fig. 6): ­ to the left ( ) for 360° Heating 360° Heating ­ to the right ( ) for Forward Only Heating (One Direction Heating) · Plug the heater into a polarized 120V outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET; it will only fit one way. Forward Only Heating (One Direction Heating) STEP 1: POWER · Press the Power button to start the heater. Your heater will automatically start on High power ( continuous run (Fig. · To turn your heater OFF simply press the Power button again. NOTE: When initially turned on, the heater will operate in continuous run mode. The heater will continue to run regardless of the room temperature in this mode. The heater is running in this mode when no LED lights are illuminated on the thermostat display. ), HZ-680C-3200-3220_OM_Rev1. qx 6/8/05 1:19 PM Page 5 HZ-3220 OPERATION (CONTINUED) S T E P 2 : H E AT O U T P U T Your unit has three output levels HIGH: 1500 Watt Heating MED: 900 Watt Heating LOW: 600 Watt Heating · Push the up button (+) to increase output level and push the down button (­) to decrease output level. [. . . ] It will, however, keep the controls from being adjusted once the heater has been set. Fig. 10 HZ-680C-3200-3220_OM_Rev1. qx 6/8/05 1:19 PM Page 6 SAFETY FEATURES These heaters are equipped with several devices and features for added protection: · SafeGuardTM Alert Heat Indicator Badge visually indicates the grille is hot by turning from black to red (HZ-3220 Series only). When the grille begins to cool after the heater is shut off the badge will turn black again. · Child Resistant push-to-turn power control knob (HZ-680C Series and HZ-3200 Series) or a child-lock feature (HZ-3220 Series). [. . . ]