User manual KEF PSW 1000.2

[. . . ] Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. Indoor use only. This marking is located on the laser protective housing inside the enclosure. This appliance is classified as a CLASS 1 LASER product. This marking is located on the rear exterior. Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems) This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. [. . . ] · [ L+R]: The sound of both the left and right channels output from each individual speaker. Press repeatedly until the desired signal appears in the front panel display. · "MAIN": Sound of the main language will be output. · "SUB": Sound of the sub language will be output. · "MAIN/SUB": Mixed sound of both the main and sub languages will be output. 39GB 3 Tuner Adjust the volume by pressing 2 +/­. If an FM program is noisy If an FM program is noisy, you can select monaural reception. There will be no stereo effect, but reception will improve. Listening to the Radio You can enjoy radio sound with the system's speakers. "/1 1 4 7 2 5 8 0 3 6 9 1 2 3 4 Press OPTIONS. The option menu appears on the TV screen. Number buttons Press X/x to select [FM Mode], then press . Press X/x to select [Monaural]. C/X/x/c, HOME FUNCTION OPTIONS PRESET +/­ TUNING +/­ x 2 +/­ Current station Current band and preset number FM 07 · [Stereo]: Stereo reception. · [Monaural]: Monaural reception. Press . The setting is made. To turn off the radio Press "/1. Presetting radio stations You can preset up to 20 stations. Before tuning, make sure to turn down the volume to minimum. 88. 00 MHz KEF FM 1 2 Press FUNCTION repeatedly until "FM" appears in the front panel display. Press and hold TUNING +/­ until the auto scanning starts. Station name (European and Russian models only) Scanning stops when the system tunes in a station. 1 2 3 4 5 6 Press OPTIONS. Press FUNCTION repeatedly until "FM" appears in the front panel display. Select the radio station. The option menu appears on the TV screen. Press X/x to select [Preset Memory], then press . Press X/x to select the preset number you want, then press . Repeat Steps 2 to 5 to store other stations. Automatic tuning Press and hold TUNING +/­ until the auto scanning starts. x The measurement is OK. 1 2 3 4 Press HOME. The home menu appears on the TV screen. Press C/c to select [Setup]. Disconnect the calibration mic, then select [OK]. The result is implemented. x The measurement is not OK. Press X/x to select [Audio Settings], then press . Press X/x to select [Auto Calibration], then press . Follow the message, then select [OK] to retry. · While the Auto Calibration function is working, do not operate the system. The confirmation display for [Auto Calibration] appears. 5 Connect the calibration mic to the A. CAL MIC jack on the rear panel. Set up the calibration mic at ear level using a tripod, etc. The front of each speaker should face the calibration mic, and there should be no obstruction between the speakers and the calibration mic. 6 7 Press X/x to select [OK]. To cancel, select [Cancel]. Press . [Auto Calibration] starts. The system adjusts the speaker settings automatically. Be quiet during the measurement. 43GB Setting the Speakers [Speaker Settings] To obtain the best possible surround sound, set connection of the speakers and their distance from your listening position. Then use the test tone to adjust the level and the balance of the speakers to the same level. The speakers in the illustration correspond to the following: 1Center speaker 2Front left speaker (L) 3Front right speaker (R) 4Subwoofer 5Surround left speaker (L) 6Surround right speaker (R) 1 2 3 4 5 Press HOME. 2 [Setup]. 1 3 The home menu appears on the TV screen. Press C/c to select 4 Press X/x to select [Audio Settings], then press . Press X/x to select [Speaker Settings], then press . A The [Speaker Settings] display appears. Press X/x to select the item, then press . 5 A 6 Check the following settings. x [Connection] If you do not connect center or surround speakers, set the parameters for [Center] and [Surround]. Since the front speaker and subwoofer settings are fixed, you cannot change them. [Front] [Front Left/Right] 3. 0 m: Set the front speaker distance. [Centre]* 3. 0 m: Set the center speaker distance. [Surround Left/Right]* 3. 0 m: Set the surround speaker distance. [. . . ] Also, the audio output differs depending on the source, connected output jack, and selected audio settings. 2)BD-RE: Ver. 2. 1 BD-R: Ver. 1. 1, 1. 2, 1. 3 including organic pigment type BD-R (LTH type) BD-Rs recorded on a PC cannot be played if postscripts are recordable. 3) A CD or DVD disc will not play if it has not been correctly finalized. For more information, refer to the operating instructions supplied with the recording device. Region code (BD-ROM/DVD VIDEO only) Your system has a region code printed on the rear of the unit and will only play a BD-ROM/ DVD VIDEO (playback only) labeled with identical region codes or ALL . Additional Information Discs that cannot be played · · · · · · · · · BDs with cartridge BDXLs DVD-RAMs HD DVDs DVD Audio discs PHOTO CDs Data part of CD-Extras Super VCDs Audio material side on DualDiscs Notes on discs This product is designed to play back discs that conform to the Compact Disc (CD) standard. [. . . ]