User manual KENWOOD CAW-CP7160

[. . . ] Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-5027-00 01 MA (K, P, Y, M, X, I) 0009 Additional Information Remote Control Operations Preparation Before applying the power Units are designed for operation as follows. Caution : Read this page carefully to ensure safe operation. 2 Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. [. . . ] No sound will be heard from the subwoofer. A+B ON : Sound from both the speakers connected to the SPEAKERS A and B terminals on the rear panel. Use this setting when listening with headphones for stereo sound in all playback modes. The indicator for the speakers you want to use should be lit. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS L LFE C S R SW LS RS · Selecting "6ch INPT" by pressing the INPUT MODE key, whereby "DVD/ 6ch" is the input source will cause SPEAKER A to be selected automatically. L LFE C S R SW LS RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO STEREO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER and ON/STANDBY keys. · The adjustment mode is displayed for approximately eight seconds. · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. Normal playback Listening to a source component VOLUME CONTROL INPUT SELECTOR Adjusting the sound MULTI CONTROL SOURCE DIRECT SOUND 21 SPEAKERS A/B PHONES VOLUME CONTROL VOLUME INPUT SELECTOR VOLUME RC-R0613 RC-R0720 INPUT SELECTOR MUTE VOLUME MULTI CONTROL SOUND SOUND MULTI CONTROL B. BOOST VOLUME MUTE RC-R0613 1 Use the INPUT SELECTOR knob to select the source you want to listen to. 1 2 3 4 5 6 7 8 9 The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob. "PHONO" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" "VIDEO2" "VIDEO3" "DVD/6ch" "AV AUX" BASS BOOST RC-R0720 Adjusting the tone You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 Press the SOUND key to select the tone mode to be adjusted. · To copy tapes using a double cassette deck, refer to the instruction manual of the double cassette deck. To cancel Press the SOURCE DIRECT key again. · If SOURCE DIRECT playback was activated while in surround mode, canceling SOURCE DIRECT playback will reactivate the previous surround mode. Listening with headphones 1 Press the SPEAKERS A or B key so that the speaker indicator goes off. Make sure the SPEAKERS indicators are turned off. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS MONITOR function (analog sources only) R RS L LFE C S LS · If you turn off all of the speakers when in surround mode, the surround mode will be canceled as well, resulting in stereo playback. 2 Connect headphones to the PHONES jack. PHONES You can connect a cassette deck or graphic equalizer to the MONITOR jacks of the receiver. If a graphic equalizer is connected, the MONITOR key should be left in the on position. Alternately, if a cassette deck equipped with a 3-head system is connected to the MONITOR jacks, you will be able to monitor the just-recorded signal while making recordings on the cassette deck. By switching the MONITOR key on and off, you can compare the sound of the source signal and the justrecorded signal. For more information, refer to the instruction manual of the connected component. 3 Use the VOLUME CONTROL knob or VOLUME keys to adjust the volume. Recording Listening to radio broadcasts The receiver can store up to 40 stations in the memory and recall them by one-touch operation. Recording video 1 Use the INPUT SELECTOR to select the video source (other than "VIDEO1") you want to record. 2 Set the video deck connected to VIDEO 1 to record. · Select the REC MODE to record a digital input source. · Recording may not be normal for some video software. [. . . ] 73 dB CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 dB Input sensitivity / impedance PHONO (MM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. 5 mV / 27 k CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV / 47 k MONITOR IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]