User manual KENWOOD CAW-HD1480

[. . . ] · During installation, do not use any screws except for the ones provided. The use of improper screws might result in damage to the main unit. · When drilling a hole in the car to fix the brackets, make sure not to damage the fuel tank, brake tube, wiring harnesses, etc. on the other side. NOTE s MD auto changer KMD-D400 s DAB tuner KTC-959DAB#1 s CD/MD changer switching unit with auxiliary RCA stereo input KCA-S210A#2 NOTE If you experience problems during installation, consult your Kenwood dealer. Cleaning the Unit If the surface is dirty, wipe it clean with a silicon cloth or soft dry cloth with the power off. · If the relevant connected device has a PROTOCOL SWITCH or O-N SWITCH, be sure to set the switch to "N" Operation will fail if set . [. . . ] #1:The KTC-959DAB cannot be used with the VZ907 . #2:AUX operation is not possible with the VZ907 . #3:Do not connect the C907 and KDC-CPS81 at the same time. The equipment will cease functioning. 2 English Installation s Accessories External view External view External view . . . . . . . . . Number of items 1 . . . . . . . . . 2 4 . . . . . . . . . 2 7 . . . . . . . . . 1 2CAUTION 2 . . . . . . . . . 4 5 . . . . . . . . . 1 8 . . . . . . . . . 1 3 . . . . . . . . . 4 6 . . . . . . . . . 1 The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. s Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the terminal of the battery. Make the proper input and output cable connections for each unit. Connect the speaker cables of the wiring harness. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. Take Connector A on the wiring harness and connect it to the external power connector on your vehicle. Connect to the terminal that is grounded when either the telephone rings or during conversation. NOTE Power control cable (Blue/ White) P. CONT TEL mute cable (Brown) TEL MUTE To connect the KENWOOD navigation system, consult your navigation manual. Ground cable (Black) (To car chassis) If no connections are made, do not let the cable come out from the tab. 4 English 2WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Connector Function Guide Pin Numbers for Cable Colour ISO Connectors Functions 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. A­7 Pin (Red) Ignition cable (Red) ACC BATT ACC BATT External Power Connector A­4 A­5 A­6 A­7 Speaker Connector B­1 B­2 B­3 B­4 B­5 B­6 B­7 B­8 Yellow Blue/White Orange Red Battery Power Control Dimmer Ignition (ACC) Vehicle Unit A­4 Pin (Yellow) Control unit Battery cable (Yellow) ACC BATT Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (­) Front Right (+) Front Right (­) Front Left (+) Front Left (­) Rear Left (+) Rear Left (­) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. A­7 Pin (Red) Ignition cable (Red) ACC Vehicle ACC Unit BATT BATT A­4 Pin (Yellow) Control unit Battery cable (Yellow) ACC BATT 3 The A-7 pin (red) of the vehicle's ISO connector is not connected to anything, whilst the A-4 pin (yellow) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Connect to a power source that can be turned on and | off with the ignition key. BATT Vehicle A­4 Pin (Yellow) Ignition cable (Red) BATT Unit Control unit Battery cable (Yellow) BATT English 5 Installation s When the control unit is the KVC-1000 Control unit (optional) KVC-1000 M4 IN OUT NAV I/F DAB control cable (Provided with the KTC-959DAB) CAW-HD1480 ANTENNA INPUT DAB DAB tuner (optional) KTC-959DAB Changer control cable (Provided with the C907) 2WARNING CD auto changer (optional) C907 Only connect black cable to TO 5L interface. Connection of light-brown connecting cable (for NAV interface use) can result in failure. s When the control unit is the VZ907 NOTE Some model cannot be connected and certain features are unavailable. For details, see IMPORTANT INFORMATION (see page 2). Control unit (optional) VZ907 TO MONITOR UNIT NAV. IF S M TO MX-BUS 2CAUTION M-S switch setting Set the M-S switch to "S". ANTENNA INPUT DAB Extention cable (5. 5 m) (Accessory7) Changer control cable (Provided with the C907) ]"N" O-N CD auto changer (optional) C907 CD/MD changer (optional) CD player (optional) KDC-CPS82, KDC-C712, KDC-C662, KMD-D400, KDC-D300, etc. 6 English FM·AM TUNER 44W×4 AMPLIFIER HIDEAWAY UNIT CAW-HD1480 M S TO MZ-BUS FM ANTENNA TO 5L I/F FRONT SPEAKER REAR SPEAKER gS h TV MONITOR 2WARNING REAR/NON-FAD PREOUT FRONT CHANGER SUB WOOFER POWER SLAVE UNIT FM ANTENNA TV MONITOR FM·AM TUNER 44W×4 AMPLIFIER HIDEAWAY UNIT CAW-HD1480 TO 5L I/F FRONT SPEAKER REAR SPEAKER SUB WOOFER Extention cable (5. 5 m) (Accessory7) REAR/NON-FAD PREOUT CHANGER FRONT TO MZ-BUS POWER SLAVE UNIT 2WARNING Changer control cable (Black) O-N ]"N" R O 24BIT RESOLUTION D/A CONVERTER N MENU KMD-D400 DISP DASC 500 750 1k 2k 4k 8k 16k 11BAND SPECTRUM ANALYZER CD/MD changer (optional) CD player (optional) KDC-CPS82, KDC-C712, KDC-C662, KMD-D400, KDC-D300, etc. CAW-HD1480 Changer control cable (Black) s When two CD/MD changers are interconnected The disk changers are distinguished by source select disk-changer 1 and disk-changer 2. NOTE If the relevant connected device has a PROTOCOL SWITCH or O-N SWITCH, be sure to set the switch to "N" . Example 1 NOTE Do not connect the C907 and KDC-CPS81 at the same time. [. . . ] · The antenna control cable is not connected. · Adverse effect of noise from power cable, etc. The memory is erased when the ignition is turned off. · The battery cable has not been connected to the proper terminal. · The ignition and battery cable are incorrectly connected. The following indications are used to inform you that there is a problem with the connections of the system. BUS-E01: The M-S switch of the Monitor connected to the BUS terminal is set to "M". [. . . ]