User manual KENWOOD CAW-RN7120

[. . . ] 16 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Setup Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 · Enter the Setup Menu Screen Setup Menu Screen · Setting the System Setup · Setting the TV Setup · Setting the Touch Panel Adjustment · Exit the Setup Menu Screen · Initializing the User Settings System Setup Screen-1 · Setting the NAV input · Setting the AV-IN1 input · Setting the AV-IN2 input · Select the AV-IN2 input display · Touch Sensor Tone [BEEP] · Switching the Setup Screen-2 · Exit the System Setup Screen -1 System Setup Screen-2 · Setting the AV Output [AV-OUT] · FM Transmitter Function [FM-TX] · Switching the Setup Screen-1 · Exit the System Setup Screen-2 TV Area Setting Screen · Setting the TV Area · Exit the TV Area Setting Screen Touch Panel Adjustment Screen · Adjusting the Touch Position The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. [. . . ] Operate the V. SEL button when the image from the device connected to AVIN2 terminal is shown on the monitor. Use this setting when there's nothing connected to the AV-IN2 terminal. [7AV-IN1] [7Off ] [7Manual] Setting the AV-IN1 input Setup switch method of the picture input to AV-IN 1 terminal. Touch [7Video 1] Setting It becomes the video mode setting. Operate the V. SEL button when the image from the device connected to AVIN1 terminal is shown on the monitor. Operate the V. SEL button when the image from the navigation unit connected to AV-IN1 terminal is shown on the monitor. [7Off ] [7NAV] English | 9 System Setup Screen-1 System Setup Screen-2 Select the AV-IN2 input display Selecting the display when this device is switched to internal AV-IN2 terminal input source. Setting the Rear view camera image [Mirror]: (AV-IN2 setting during "R-Cam") Touch Setting [7On] The image which appeares in the camera is turned left-side right and displayed. [7Off ] The image which appeares in the camera is displayed as it is. Setting the AV Output [AV-OUT] Touch [7Normal] [7Video 1]/ [7NAV] [7Video 2]/ [7R-Cam] [7TV] Setting Picture/sound with monitor picture. (During the KTC-V500P is connected) FM Transmitter Function [FM-TX] You can use the FM transmitter function to hear the sound of the source set in AV OUT from your car FM radio. Touch [7On] [7Off ] Setting The FM transmitter is turned on. The FM transmitter is turned off. Touch Sensor Tone [BEEP] Setting the operation check sound (beep sound) ON/OFF. Make sure only to use the accessories shipped with the unit, as shown above. 16 | English Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the · terminal of the battery. Make the proper input and output cable connections for each unit. Connect the wiring harness wires in the following order: ground, battery, ignition. Connect the wiring harness connector to the unit. Reconnect the · terminal of the battery. (See page 3) 2WARNING · This product is intended for use with 12V DC negative ground power only. Do not connect it to any other power supply. · To prevent shorting, disconnect the battery cable from the negative terminal of the battery during installation. · Be sure to firmly stabilise this product. Do not install it in a location which is not stable. [. . . ] undisturbed for 24 hours. Accessory D 5 After attaching the stand, allow it to sit Tighten Loosen Tighten 6 Take care not to apply any force to the stand during this time. 7 Fully loosen the installation screws, align the slit on the rear of the unit with the installation shoe and slide the monitor unit onto the stand. 8 Adjust the height, horizontal angle and vertical angle of the monitor and securely tighten the installation screws. You can also adjust the monitor unit's forward position by loosening the angle adjustment knobs and adjusting the angle of the monitor unit's installation stand. · Attach the monitor to the bracket securely until it clicks. Loosen Accessory G Protective strip Installation surface 20 | English Installation Attaching the Harness Band Secure the cable to the bracket using the supplied harness band (Accessory J) . Accessory J Removing the Monitor Unit Raise the Release button. The Monitor Unit is unlocked, allowing you to detach it. Release button English | 21 Installation Installation for Video Box Unit Securing to audio board 1 Use the screws (Accessory F) to fix the bracket (Accessory C) onto both sides of Video Box Unit. Accessory F Accessory C Accessory F 2 Use screws (Accessory E) to fix Video Box Unit onto an audio board or another. Accessory E Securing to pile carpet Peel the protective strips off of the velcro strips (Accessory H), attach them to the bottom of the Video Box Unit, and secure to the pile carpet. . · Please do not install the unit near the dashboard, the rear tray, or other important components. [. . . ]