User manual KENWOOD CT-203

[. . . ] STEREO CASSETTE DECK CT/KXF-W SERIES CT-203 CT-2050 KXF-W4010 KXF-W6010 INSTRUCTION MANUAL KENWOOD CORPORATION This manual contains instructions for four models. Model availability and features (functions) may differ depending on country and sales area. SI DICHIARA CHE : gli apparecchi Sintonizzatori per casa Kenwood modelli KT-2080, KT-3080 rispondono alle prescrizioni dell'art. Fatto a Milano il 15 febbraio 1996 Kenwood Electronics Italia S. p. A. Sirtori, 7/9 - 20129 Milano B60-3706-00 HZ ( K, P, T, M, X, Y ) ID 99/3 2 1 98/12 11 10 9 8 7 6 5 4 3 Introduction CT-2050/203/KXF-W6010/W4010 (En/M) 2 Before applying power Units are designed for operation as follows. Caution : Read this section carefully to ensure safe operation. U. S. A. [. . . ] ÷ The deck enters the stop mode automatically when the tape has been recorded till the end. Bias level adjustment (Deck B of the CT-2050/KXF-W6010 only) The MODE key can be used to adjust the bias level. 1 Press the MODE key and select the "BIAS" mode. MODE Each press of the MODE key changes the setting. 1 "LEVEL" lights up: Recording level setting mode 2 "BAL. " lights up: Recording balance setting mode 3 "BIAS" lights up: Recording bias setting mode (Deck B of the CT-2050/KXF-W6010 only) 4 "LEVEL", "BAL. ", and "BIAS"go off: Counter display mode lights up 2 Adjust the bias level. REC LEVEL/BAL. /BIAS MIN/L MAX/R The high frequency decreases. The high frequency increases. ÷ To adjust the bias level, play back the recorded sound and adjust to the suitable level. Repeat if necessary. ÷ The bias can be adjusted to a value of ±3. How to use the MPX FILTER key Use this function when recording a radio (FM) broadcasts. Depending on the tuner, a recorded FM broadcast may produce a "beat" sound. In this case, press the MPX FILTER key before recording. To cancel, press the MPX FILTER key again. lights up MPX FILTER How to record (CT-203/KXF-W4010; Deck B only) CT-2050/203/KXF-W6010/W4010 (En/M) 18 To pause recording temporarily Pause 8PAUSE To stop recording 1 Stop the tape transport. CT-2050/KXF-W6010 2 7 3 To resume recording ¶REC/ARM CT-203/KXF-W4010 ÷ The 8 indicator lights. 2 Stop playing the source component. How to provide non-recorded blanks between programs In stop mode Press successively twice. During recording Press once. ¶REC/ARM ¶REC/ARM ÷ After leaving a non-recorded blank of about 4 seconds, the deck enters the record-pause mode. To start recording again from the biginning The following procedure is useful when you want to cancel recording in progress and re-start it. A non-recorded space of about 4 seconds or more should be reserved before the position where recording was started. 1 Rewind during recording. During recording in the 3 direction: 1 ¡ ÷ When the ¡ (or 1) key is pressed during recording, recording is aborted and tape is rewound as shown below if there is a non-recorded space of more than 4 seconds before the recording start position. Tape stops after 2 sec. of transport. Re-recording Recorded tune Tune to be re-recorded. During recording in the 2 direction: 1 ¡ Blank of 4 sec. or more. 2 Press the REC/ARM (¶) key twice. CT-2050/KXF-W6010 ÷ If there is no recorded tune before, the tape will be rewound then stopped. ÷ When re-recording from the beginning of tape, feed the leader tape (the first portion of tape that cannot be recorded) before starting rerecording. ¶REC/ARM CT-203/KXF-W4010 ÷ A non-recorded space of about 4 seconds is reserved on tape, then the tape transport stops. 3 Replay the tune you wish to record. 4 Press the REC/ARM (¶) key once. ¶REC/ARM ÷ Recording starts. Relay recording (CT-2050/KXF-W6010 only) CT-2050/203/KXF-W6010/W4010 (En/M) This function allows to record sound continuously from deck A to B. Since this unit is not designed for recording with metal ) tapes, do not use metal tapes for recording. (TYPE 19 Preparation Make "Playback (recording) preparation". 0 (If relay recording is required, insert tapes in both decks A and B. Select the recording mode to set to "O" or "[" only. ) : Keys and control used in the operations described on this page. Relay recording 1 Set the relay recording mode. "RELAY" lights up. RELAY REC 2 Perform auto-bias adjustment. (The bias adjustment is applied to deck B. ) "AUTO BIAS"blinks. AUTO BIAS After approximately 40 seconds "AUTO BIAS" lightsup. 3 Adjust the recording level. 1 Play the music source. 3 Adjust the recording balance and recording level. ^ 4 Stop playing the music source. ÷ The optimum bias is set in about 40 seconds, after which the deck enters the stop mode. ÷ Recording is possible even if the auto-bias adjustment operation is omitted. 4 Start recording. 1 Press the REC/ARM (¶) key (of deck A). ¶REC/ARM ÷ Recording will start. [. . . ] 775 mV/1. 0 k Headphones . . . . . . . . . . . . . . . . . . . 0. 5 mW/32 [General] Power Consumption . . . . . . W: 440 mm (15-3/4") H: 134 mm (5-9/16") D: 369 mm (15-3/8") Weight (Net) . . . . . . . . . . . . . . . . . . . . 4. 6 kg (10. 6 lb) CT-203/KXF-W4010 Track System . . . . . . . . . . . . . . . . . [. . . ]