User manual KENWOOD DDX7032

[. . . ] € If the power is not turned ON (“PROTECT” is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. € Make sure that all wire connections are securely made by inserting jacks until they lock completely. [. . . ] 31 1:34:41 PM Connection Ignition key switch ACC If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. A B A B C Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) (To car chassis) Antenna Cord FM/AM antenna input Car fuse box Car fuse box (Main fuse) C Battery Connect to the vehicle's parking brake detection switch harness using the supplied relay connector. Parking sensor wire (Light Green) PRK SW For the sake of safety, be sure to connect the parking sensor. Connect to vehicle's reverse lamp harness when using the optional rear view camera. To steering remote To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. When this terminal is not in use, leave its cap on. To car light control switch Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. When using the optional power amplifier, connect to its power control terminal. " terminal of the amplifier having the external amp control function. Reveres sensor wire (Purple/White) Steering remote control input (Light Blue/Yellow) Dimmer control wire (Orange/White) Mute wire (Brown) Motor antenna control wire (Blue) Power control wire (Blue/White) External amplifier control wire (Pink/Black) If no connections are made, do not let the cable come out from the tab. CONT + To front right speaker + To rear left speaker Purple/Black P CONT Purple + To rear right speaker EXT. Accessory 2 Accessory 3 Accessory 4 AV OUT ■ Audio/Video Output • Video output (Yellow) • Audio left output (White) • Audio right output (Red) ■ Audio/Video Input1 • Video input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Rear View Camera Input • Video input (Yellow) ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■ Subwoofer Preout • Audio left output (White) • Audio right output (Red) RELAY 2 RELAY 1 SUB WOOFER REAR FRONT REAR VIEW CAMERA AV IN1 To Relay Box 6 | DNX7120/DDX712/DDX7032 DNX_DDX7_insta_K_En_r1. 31 1:34:43 PM Optional Accessory Connection iPod (commercially available) To GXM30/ GTM10 When connecting the XM Tuner GXM30 (optional accessory) or TMC Tuner GTM10 (optional accessory), put the cable clamper (accessory $) to the back of this unit first, and then wire the cable through the clamper. Audio Output (Black) Audio Input KCA-iP300V (Optional Accessory) Accessory 5 Video Output (Yellow) Video Input Accessory $ USB terminal USB terminal To SIRIUS Satellite Radio tuner/ XM Satellite Radio tuner/ HD Radio tuner/KCA-BT200 (Optional Accessory) Conversion adapter (Optional Accessory) may be necessary for connection of Optional Accessory. Contact your Kenwood dealer for details. [. . . ] Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. Remove the Hex-head screw with integral washer (M4 × 8) on the back panel. Insert the two removal tools 6 deeply into the slots on each side, as shown. [. . . ]