User manual KENWOOD DDX7032M

[. . . ] Reconnect the - terminal of the battery. Press the reset button. ¤ · If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. [. . . ] · If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. · If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. · If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with the same rating. · Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. · Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. · When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. Yellow Blue/White Orange/White Red Black Battery Power Control Dimmer Ignition (ACC) Earth (Ground) Connection Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (­) Front Right (+) Front Right (­) Front Left (+) Front Left (­) Rear Left (+) Rear Left (­) 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A4 pin (yellow) is connected to the constant power supply. Ignition cable (Red) Unit Battery cable (Yellow) A-7 Pin (Red) Vehicle A-4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Ignition cable (Red) Unit Battery cable (Yellow) A-7 Pin (Red) Vehicle A-4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle's ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Ignition cable (Red) Unit Battery cable (Yellow) A-7 Pin (Red) Vehicle A-4 Pin (Yellow) / · When the connection is made as in 3 above, the unit's power will not be linked to the ignition key. For that reason, always make sure to turn off the unit's power when the ignition is turned off. To link the unit's power to the ignition, connect the ignition cable (ACC. . . red) to a power source that can be turned on and off with the ignition key. 6| DDX7032M System Connection USB terminal USB device (commercially available) Do not connect. Rear view AV OUT Audio/Visual Output · Visual output (Yellow) AV IN REAR VIEW CAMERA Audio/Visual input · Visual input (Yellow) · Audio left input (White) · Audio right input (Red) Rear View Camera Input · Visual input (Yellow) Front Preout · Audio left output (White) · Audio right output (Red) Rear Preout · Audio left output (White) · Audio right output (Red) Subwoofer Preout · Audio left output (White) · Audio right output (Red) Audio/Visual Output · Audio left output (White) · Audio right output (Red) Audio Input Resistance-free stereo type mini plug Visual Input Resistance-free mini plug English | iPod VIDEO IN iPod AUDIO IN AV OUT SUB WOOFER REAR FRONT 7 Optional Accessory Connection iPod (commercially available) Navigation System (Optional Accessory) KCA-iP300V (Optional Accessory) Audio Output (Black) Audio Input iPod AUDIO IN Connection cable (Included in the Navigation System) Visual Input iPod VIDEO IN Visual Output (Yellow) Rear view USB terminal USB terminal Connection cable (Included in the Disc changer) Disc Changer etc. (Optional Accessory) Connection cable (Included in the TV tuner) 8| DDX7032M TV ANTENNA INPUT TO MONITOR UNIT TV Tuner (Optional Accessory) Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Metal mounting strap (commercially available) Accessory 2 Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). English | 9 Removing Monitor/Player Unit Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 3 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Removal Tool (Accessory 3) Removing the Unit 1. [. . . ] Engage the catch pins on the removal tool 3 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Removal Tool (Accessory 3) Removing the Unit 1. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. [. . . ]