User manual KENWOOD DDX812

[. . . ] The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. € When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. € After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. [. . . ] If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. 18 7:47:42 PM Connection Ignition key switch ACC If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. A B A B Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) (To car chassis) Antenna Cord FM/AM antenna input Car fuse box Car fuse box (Main fuse) C Battery C Connect to the vehicle's parking brake detection switch harness. Parking sensor wire (Light Green) PRK SW For the sake of safety, be sure to connect the parking sensor. Connect to vehicle's reverse lamp harness when using the optional rear view camera. To steering remote Reveres sensor wire (Purple/White) Steering remote control input (Light Blue/Yellow) To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. When this terminal is not in use, leave its cap on. Dimmer control wire (Orange/White) To car light control switch Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. When using the optional power amplifier, connect to its power control terminal. " terminal of the amplifier having the external amp control function. Motor antenna control wire (Blue) Mute wire (Brown) Power control wire (Blue/White) External amplifier control wire (Pink/Black) If no connections are made, do not let the cable come out from the tab. CONT White/Black White Gray/Black ILLUMI + To front left speaker Gray MUTE + To front right speaker Green/Black Green Purple/Black + To rear left speaker ANT. 5φ) To XM Tuner GXM30 or TMC Tuner GTM10 (optional accessory) (DNX8120 only) Accessory % When connecting the XM Tuner GXM30 (optional accessory) or TMC Tuner GTM10 (optional accessory), put the cable clamper (accessory %) to the back of this unit first, and then wire the cable through the clamper. Accessory 2 Accessory 3 Accessory 4 AV OUT ■ Audio/Visual Output • Visual output (Yellow) • Audio left output (White) • Audio right output (Red) ■ Audio/Visual input1 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Audio/Visual input2 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Rear View Camera Input • Visual input (Yellow) ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■ Subwoofer Preout • Audio left output (White) • Audio right output (Red) ■ Center Preout • Audio output (Black) To Relay Box 6 | DNX8120/DDX812/DDX8032BT B54-4648-00_00_EN. USB terminal To SIRIUS Satellite Radio tuner/ XM Satellite Radio tuner/ HD Radio tuner (Optional Accessory) Conversion adapter (optional accessory) may be necessary for connection of optional accessory. Contact your Kenwood dealer for details. 18 7:47:45 PM Installing the GPS Antenna (DNX8120 only) GPS antenna is installed inside of the car. It should be installed as horizontally as possible to allow easy reception of the GPS satellite signals. To mount the GPS antenna inside your vehicle: 1. [. . . ] Lower the frame and pull it forward as shown in the figure. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. Remove the Hex-head screw with integral washer (M4 × 8) on the back panel. Insert the two removal tools 6 deeply into the slots on each side, as shown. [. . . ]