User manual KENWOOD DNX5310BTM

[. . . ] Display "AUTO1" "AUTO2" "MANU" Setting Tunes in a station with good reception automatically. Tunes in stations in memory one after another. Switches to the next frequency manually. Manual Memory Stores the current receiving station in memory. 1 Select a station you wish to store in memory 2 Store in memory Next page 3 The above operation example with the mark differs from the actual operation. 4 DNX5310BTMBT/DNX5310BTM/DDX5022/DDX5022Y/DDX52RY English 5 Before Use 2WARNING To prevent injury or fire, take the following precautions: · To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. [. . . ] 3 Make a call If the voice recognition is succeeded and there is only one phone number found: / · The Outgoing Calls list screen or Incoming Calls list screen shows the list of the calls originated from or received at this unit. They are not the ones stored in the cell-phone memory. 3 Make a call. 3 Displays the phonebook list. 50 DNX5310BTMBT/DNX5310BTM/DDX5022/DDX5022Y/DDX52RY If you hear another Beep sound: Speak the key word within 2 seconds after the Beep, or touch the [Phonebook List] button to select the phone number. Setting Up the Hands-Free Phone The Hands-Free system can be set as follows. 1 Display the Hands Free Setup screen Make a call. / · If there are more than one phone numbers registered under the same name, and the key word voice is registered for each phone number, you will hear another beep. For how to register key word, see <Key Word Voice Recognition> (page 53). If there are more than one phone numbers registered under the same name, go to step 3. 3 Select a Phone number category 4 6 5 7 2 Setup each item 1 2 3 4 5 6 8 7 4 Calls the displayed phone number. 5 Creates an SMS to the displayed address. See <SMS (Short Message Service)> (page 55). 4 Make a call 8 9 10 11 12 / · A message is displayed if the voice is not recognized. Read the message for the further operation. 1 Moves to the "Hands Free Setup 2" screen. 2 Sets an automatic response time after call termination. 3 Cancels voice registration. Utter within 2 seconds after the Beep. 4 Utter the voice to register (2nd try) 52 DNX5310BTMBT/DNX5310BTM/DDX5022/DDX5022Y/DDX52RY 5 End voice registration 3 Plays voice registered for the selected Phone number category. 4 Deletes voice registered for the selected Phone number category. Touch to display the confirmation screen. Touch [YES] to delete or [NO] to cancel. 5 Returns to the Hands-Free Set Up screen. 3 Display voice registration screen / · A message is displayed if the voice is not recognized. Read the message for the further operation. · Repeat from 1st try if the voice is different from the 1st try. 4 Utter the voice to register (1st try) 7 Key Word Voice Recognition Registers the voice to select the Phone number category by Voice Recognition. 1 Display the Key Word List screen Display the "Hands Free" screen and touch [Setup]. See <Control Screen Function> (page 45). 6 6 Registers the voice. [. . . ] Although the effective pixels for the liquid crystal panel is given as 99. 99% or more, 0. 01% of pixels may not light or may light incorrectly. English 93 The marking of products using lasers (Except for some areas) CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. Information on Disposal of Old Electrical and Electronic Equipment (applicable for EU countries that have adopted separate waste collection systems) Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment should be recycled at a facility capable of handling these items and their waste byproducts. [. . . ]