User manual KENWOOD DNX6160

[. . . ] The power supply must be connected to the wires via the fuse. 1 5 Acquiring GPS Signals The first time you turn on DNX SERIES, you must wait while the system acquires satellite signals for the first time. This process could take up to several minutes. Make sure your vehicle is outdoors in an open area away from tall buildings and trees for fastest acquisition. [. . . ] Cooling fan • Reception may drop if there are metal objects near the Bluetooth antenna. (DNX6960/ DNX6160/ DNX6020EX/ DNX6460BT/ DDX616/ DDX6046BT only) Bluetooth antenna unit ¤ CAUTION Install this unit in the console of your vehicle. Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot. 11 5:36:01 PM Connection Ignition key switch connect (red) and the battery ¤ If you(yellow) tothe ignition wire(ground), you may wire the car chassis cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. ACC A B A B C Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) (To car chassis) Antenna Cord FM/AM antenna input Car fuse box Car fuse box (Main fuse) C Battery Connect ⁄ detectionto the vehicle's parking brake switch harness. Parking sensor wire (Light Green) PRK SW For the sake of safety, be sure to connect the parking sensor. Reveres sensor wire (Purple/White) Connect to vehicle's reverse lamp harness when using the optional rear view camera. To steering remote Steering remote control wire (Light Blue/Yellow) ⁄ To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. When this terminal is not in use, leave its cap on. Dimmer control wire (Orange/White) To car light control switch Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Mute control wire (Brown) ⁄ Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. When using the optional power amplifier, connect to its power control terminal. Motor antenna control wire (Blue) Power control wire (Blue/White) ⁄ 4 | DNX SERIES/ DDX SERIES If no connections are made, do not let the cable come out from the tab. 11 5:36:02 PM Bluetooth Microphone (Accessory 2) (see page 8) GPS Antenna (Accessory 3) (see page 8) FUSE ( 15A ) Accessory 1 REVERSE REMOTE CONT STEERING WHEEL REMOTE INPUT White/Black White Gray/Black + To front left speaker ILLUMI Gray MUTE + To front right speaker Green/Black Green Purple/Black + To rear left speaker ANT. 5φ) To TMC Tuner GTM10 (optional accessory) (DNX6960/ DNX6160/ DNX6020EX/ DNX5160 only) Accessory 9 When connecting the TMC Tuner GTM10 (optional accessory), put the cable clamper (accessory 9; DNX6960/ DNX6160/ DNX6020EX/ DNX5160 only) to the back of this unit first, and then wire the cable through the clamper. Rear Preout • Audio left output (White) • Audio right output (Red) Front Preout • Audio left output (White) • Audio right output (Red) Subwoofer Preout • Audio left output (White) • Audio right output (Red) 6 | DNX SERIES/ DDX SERIES B54-4761-00_00_DNX6-5_K_En_r1. 11 5:36:02 PM Optional Accessory Connection iPod (commercially available) KCA-iP301V (Optional Accessory) Audio Output (Black) Visual Output (Yellow) (DDX SERIES only) USB terminal Navigation System (Optional Accessory) To SIRIUS Satellite Radio tuner/ XM Satellite Radio tuner/ HD Radio tuner (Optional Accessory) Connection cable (Included in the Navigation System) ⁄ Conversion adapter (optional accessory) may be necessary for connection of optional accessory. [. . . ] Engage the catch pins on the removal tool 8 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. Insert the two removal tools 8 deeply into the slots on each side, as shown. [. . . ]