User manual KENWOOD DNX7160

[. . . ] This process could take up to several minutes. Make sure your vehicle is outdoors in an open area away from tall buildings and trees for fastest acquisition. After the system acquires satellites for the first time, it will acquire satellites quickly each time thereafter. 1 8 About the Front Panel When removing the product from the box or installing it, the front panel may be positioned at the angle shown in (Fig. [. . . ] Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction. €¢ Do not press hard on the panel surface when installing the unit to the vehicle. Otherwise scars, damage, or failure may result. €¢ Reception may drop if there are metal objects near the Bluetooth antenna. Bluetooth antenna unit ¤ CAUTION Install this unit in the console of your vehicle. Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot. English 3    DFPKA$ Connection Ignition key switch ACC Ignition wire (Red) Battery wire (Yellow) Car fuse box (Main fuse) Car fuse box Antenna Cord Ground wire (Black) (To car chassis) ignition (red) and battery wire (yellow) ¤ If you connect the(ground), wire may causetheshort circuit, that in to the car chassis you a turn may start a fire. Always connect those wires to the power source running through the fuse box. a A FM/AM antenna input Battery Connect ⁄ detectionto the vehicle's parking brake switch harness. Parking sensor wire (Light Green) PRK SW For best safety, be sure to connect the parking sensor. Connect to vehicle's reverse lamp harness when using the optional rear view camera. To steering remote To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matched to your car is required. „ To car light control switch Connect to the terminal that is grounded when either the telephone rings or during conversation. „ To connect the Kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. When using the optional power amplifier, connect to its power control terminal. „ 4 DNX SERIES If no connections are made, do not let the cable come out from the tab.    DFPKA$ Bluetooth Microphone (Accessory #) (see page 8) Cooling fan GPS Antenna (Accessory !) (see page 8) FUSE ( 15A ) Accessory 1 Reverse sensor wire (Purple/White) REVERSE To front left speaker White/Black White + Steering remote control input (Light Blue/Yellow) REMOTE CONT STEERING WHEEL REMOTE INPUT To front right speaker Gray/Black Gray + Dimmer control wire (Orange/White) ILLUMI Mute control wire (Brown) MUTE To rear left speaker Green/Black Green + Motorized antenna control wire (Blue) ANT. 5φ) Accessory $ ⁄ Accessory 3 Accessory 2 Accessory 4 When connecting the TMC Tuner GTM10 (optional accessory), put the cable clamper (accessory $) to the back of this unit first, and then wire the cable through the clamper. AV OUT To Camera control terminal (Green/Red) Audio/Visual Output • Visual output (Yellow) • Audio left output (White) • Audio right output (Red) Audio/Visual Input • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) Rear View Camera Input • Visual input (Yellow) (Green/White) To Relay Box RELAY 1 RELAY 2 (Blue/Red) FRONT (Blue/Red) REAR VIEW CAMERA AV IN SUB WOOFER Front Preout • Audio left output (White) • Audio right output (Red) Rear Preout • Audio left output (White) • Audio right output (Red) Subwoofer Preout • Audio left output (White) • Audio right output (Red) 6 DNX SERIES REAR    DFPKA$ Optional Accessory Connection iPod (commercially available) KCA-iP301V (Optional Accessory) Visual Output (Yellow) Audio Output (Black) USB terminal USB terminal To SIRIUS Satellite Radio tuner/ XM Satellite Radio tuner/ HD Radio tuner (Optional Accessory) ⁄ Conversion adapter (optional accessory) may be necessary for connection of optional accessory. [. . . ] Engage the catch pins on the removal tool 5 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. Insert the two removal tools 5 deeply into the slots on each side, as shown. [. . . ]