User manual KENWOOD DPF-J5010

[. . . ] Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction. AC 110 ­ 120V AC 220 ­ 240V Note: Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selector switch. Move switch lever to match your line voltage with a small screwdriver or other pointed tool. Safety precautions RAIN OR MOISTURE. CAUTION R I S OF F E L E C T R I SHOCK RISK K O ELECTRIC C S H O C K D NOT OPEN DO O N O T O P E N Caution : Read this section carefully to ensure safe operation. WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS. THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. The marking of products using lasers (Except for some areas) CLASS 1 LASER PRODUCT The marking is located on the rear panel and says that the component uses laser beams that have been classified as Class 1. [. . . ] ÷ Do not place any objects impairing heat radiation onto the top of unit. ÷ Leave a space around the unit (from the largest outside dimension including projection) equal or greater than, shown below. Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm DIGITAL OUTPUT jack Connection to KENWOOD CD TEXT MD recorder; The text (track titles) and the music of a CD can be copied to an MD. For details, refer to the MD instruction manual. OUTPUT DIGITAL OUTPUT OPTICAL SYSTEM CONTROL TEXT L R Remove the protection cap when using the DIGITAL OUTPUT (OPTICAL) jack. To AC outlet SYSTEM CONTROL System control cord CD L Audio cord R Amplifier To wall AC outlet DIGITAL INPUT OPTICAL Commercially-available optical fiber cable MD recorder/CD-R To AC outlet Notes 1. If connections are loose there could be loss of sound or noise produced. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging/unplugging connection cords without removal of the power cord can cause malfunctions or damage to the unit. System connections 7 Connection to a general-use amplifier Use the provided audio cords to connect the OUTPUT jacks of this unit to the CD input jacks (or AUX jacks) of the amplifier. Connection to digital amplifier, MD or CD-R Connect the DIGITAL OUTPUT (OPTICAL) jack to the digital input jack of the amplifier, DAT recorder, MD recorder, etc. , using an optical fiber cable (sold separately) which are commercially available in audio stores. Do not connect system control cords to any components other than those specified by Kenwood. It may cause a malfunction and damage your equipment. Be sure the system control plugs are inserted all the way in to the system control terminals. Notes SYSTEM CONTROL OPERATIONS Remote Control Lets you operate this unit with the system remote control unit supplied with the amplifier or receiver. Automatic Operation Automatically switches the input selector on the amplifier or receiver when you start playback from this unit. Synchronized Recording Lets you synchronize recording with the start of playback when recording from CD. Also, the simple CCRS operation lets you make great recordings from CD. Therefore, their lives may be shorter than ordinary batteries. When the remote-controllable distance gets shorter than before, replace both batteries with new ones. Malfunction may occur if direct sunlight or the light of a high-frequency lighting fluorescent lamp enters the remote control light sensor. In such a case, change the system installation position to prevent the malfunction. Normal play (TRACK mode) Use the following procedure to play a CD in the original order of tracks from track No. 1. 12 The figure shows an example for the DPF-2030 0 7 4 1 6 ¢ ¡ : Keys and control used in the operations described on this page. Playing tracks in order from track No. 1 1 Press the POWER switch to ON. POWER 0 - ON ­ OFF ÷ Playback starts when a disc has been loaded. 2 Load a disc. 1 Open the tray. OPEN/CLOSE 0 0 2 Place a disc. Label side 0 7 4 6 ¢ Disc tray 1 ¡ ÷ Do not touch the played side of disc. ÷ Loading two discs together will cause malfunctioning. ÷ Place the disc properly along the groove on the tray. (If the disc is not placed horizontally, malfunction will result. ) ÷ A single CD (8 cm disc) can also be played. ÷ Ordinary CD single (8 cm) disc adapters sold in audio stores cannot be used with this unit. Lights up. TRACK 3 Close the tray. OPEN/CLOSE 0 0 TRACK NO. SINGLE TIME 01 1 6 2 7 3 8 4 9 5 10 0 : 00 The track Nos. recorded on the CD are displayed. 3 Start playback. 0 ÷ After a few seconds, play starts from the track No. [. . . ] ÷ If automatic play is not required, remove the disc from the player before setting the unit to POWER OFF. No sound. ÷ Play mode is not entered. ÷ The connection cords are inserted loosely. ÷ Output level is attenuated too low. ÷ Oscillation is applied to this unit. Music is interrupted. [. . . ]