User manual KENWOOD DPX-MP4050B

[. . . ] • Characters that conform to GB2312 or ISO 8859-1 can be displayed. Refer to “MENU” > “Chinese” of <Function Control> (page 6). • In this document, the description indicator will light means a status is displayed. Refer to <About Display Type> (page 8) for the details of the status display. [. . . ] When “Re-Enter” is displayed, “SECURITY SET” is also displayed. 5 Exit Security Code mode Press the [FNC] button. ⁄ • If a wrong security code is entered, “Error” is displayed. Enter a correct security code. 5 Do the step 3 through 4 operation, and reenter the Security Code. The Security Code function activates. ⁄ • If you enter the wrong Code in steps 3 through 4, repeat from step 3. 6 Exit Security Code mode Press the [FNC] button. Entering Security Code The Security Code is required to use the audio unit when the unit is first used after removed from the battery power source or the Reset button is pressed. 1 Turn the power ON. 2 Do the step 3 through 4 operation, and enter the Security Code. Now, you can use the unit. English | 15 B64-4231-00_00_DPXMP6110_e. indd 15 08. 7. 9 9:59:19 AM Other Functions Manual Clock Adjustment 1 Select Clock Adjustment item during Menu mode Select the “Clock Adjust” display. For how to select Function Control items, refer to <Function Control> (page 6). Demonstration mode setting Turning the demonstration mode ON/OFF. 1 Select Demonstration item during Menu mode Select the “DEMO Mode” display. For how to select Function Control items, refer to <Function Control> (page 6). 2 Enter Clock adjustment mode Press the Control knob for at least 1 second. The clock display blinks. 2 Set the Demonstration mode Press the Control knob for at least 2 seconds. Pressing this button for 2 seconds or longer toggles the setting between “ON” and “OFF”. 3 Adjusting Clock Operation type Selecting the item (hours or minutes) Adjust each item Operation Push the Control knob towards right or left. Turn the Control knob or push it towards up or down. 3 Exit Demonstration mode Press the [FNC] button. When LX AMP unit connecting 4 Exit Clock adjustment mode Press the [FNC] button. AMP Control You can control the LX AMP connected to the unit. 1 Select AMP Control item during Menu mode Date Adjustment 1 Select Date Adjustment item during Menu mode Select the “Date Adjust” display. For how to select Function Control items, refer to <Function Control> (page 6). For how to select Function Control item, refer to <Function Control> (page 6). ⁄ • When you select “User” at <Preset position selection> (page 18), the adjusted setting value will be recalled. 3 Recall the Audio Preset Audio Preset Memory Registering the value setup by Sound Control. The memory cannot be erased by the Reset button. “Recall?” is displayed. 4 Turn the Control knob to select “YES”, and then press the Control knob. “Recall Completed” is displayed. 1 Setup Sound Control Refer to the following operations to setup the Sound Control. - Cabin selection (page 17) - DTA (Digital Time Alignment) setting (page 17) - X’Over setting (page 17) - Equalizer Control (page 18) - Preset position selection (page 18) - Manual position setting (page 19) 5 Exit Audio Preset Recall mode Press the [FNC] button. ⁄ • The User memory of “SYSTEM Q” in <Equalizer Control> (page 18) is changed to the value which was recalled. • The source tone memory item of <Equalizer Control> (page 18) is changed to the value which was recalled by the selected source. 2 Enter Audio Preset Memory mode Select “SOUND” > “PRESET” > “MEMO”. For how to select Function Control item, refer to <Function Control> (page 6). English | 19 B64-4231-00_00_DPXMP6110_e. indd 19 08. 7. 9 9:59:21 AM Audio Adjustments Audio Control You can adjust following Audio Control items ; Adjustment Item Display Range Rear volume “REAR VOLUME” 0 — 35 Balance “BALANCE” Left 15 — Right 15 Fader “FADER” Rear 15 — Front 15 Exit Audio Control mode (Volume control mode) Audio Setup You can set Sound system , such as follows; Adjustment Item Display Volume offset “VOL-OFFSET” Dual Zone System “2 ZONE” Range –8 — ±0 (AUX: -8— +8) OFF/ON ⁄ • Volume offset: Sets each source’s volume as a difference from the basic volume. • Dual Zone System Main source and sub source (Auxiliary input) output Front channel and Rear channel separately. - Set up the channel of sub source by “Zone2” of <Function Control> (page 6). - Adjust the volume of Front channel by [AUD] knob. [. . . ] If the “Error 77” code does not disappear, consult your nearest service center. USB ERROR (Blink): Some trouble may have occurred to the connected USB device. ➪ Remove the USB device, then cycle the power switch to ON. If the same display is repeated, use another USB device. [. . . ]