User manual KENWOOD DPX503

[. . . ] DPX503 DPX303 DUAL DIN SIZED CD RECEIVER INSTRUCTION MANUAL RECEPTEUR CD FORMAT DUAL DIN MODE D’EMPLOI RECEPTOR DUAL DE CD TAMAÑO DIN MANUAL DE INSTRUCCIONES Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new DUAL DIN SIZED CD RECEIVER. For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. [. . . ] X’Over setting You can set a X’Over value for the speakers; Adjustment Item Display Front High Pass Filter “HPF-Front” Rear High Pass Filter Low Pass Filter Subwoofer level Subwoofer Phase Range Through/40/60/80/100/120/ 150/180/220 Hz “HPF-Rear” Through/40/60/80/100/120/ 150/180/220 Hz “LPF” 50/60/80/100/120/Through Hz “SUB-W LEVEL” –15 — +15 “SW PHASE” Reverse (180°)/ Normal (0°) 3 Set the value Turn the Control knob. 4 Exit Equalizer Control mode Press the [FNC] button. Function of DPX503 Preset position selection According to the listening position, select the position from the following settings so that the normal position of the sound environment can be compensated in accordance with the selected position; Compensation seat Not compensating. Front-Left seat Front-Right seat Front seat Calls the value adjusted at <Manual position setting> (page 21). 2 Select the item you want to set Turn the Control knob and push the center when the desired item is displayed. 3 Set the X’Over value Turn the Control knob. Equalizer Control You can adjust following Equalizer Control items ; Adjustment Item Display System Q “Preset EQ” Range “NATURAL” (Natural)/ “USER” (User setting)/ “ROCK” (Rock)/ “POPS” (Pops)/ “EASY” (Easy)/ “TOP40” (Top 40)/ “JAZZ” (Jazz)/ ”GAME” (Game) –8 — +8 –8 — +8 –8 — +8 2 Select the seat you want to compensate Turn the Control knob. 3 Exit Position setting mode Press the [FNC] button. Bass level* Middle level* Treble level* “Bass” “Middle” “Treble” * Source tone memory: Puts the set up value in the memory per source.  • “USER”: The ranges selected lastly for Bass level, Middle level, and Treble level are recalled automatically. The memory cannot be erased by the Reset button. 1 Setup Sound Control Refer to the following operations to setup the Sound Control. - Cabin selection (page 19) - DTA (Digital Time Alignment) setting (page 19) - X’Over setting (page 20) - Equalizer Control (page 20) - Preset position selection (page 20) - Manual position setting (page 21) 2 Select the speaker you want to adjust Item “Front Lch” “Front Rch” “Rear Lch” “Rear Rch” “Sub Lch” “Sub Rch” Setting overview Front Left speaker Front Right speaker Rear Left speaker Rear Right speaker Subwoofer Left Subwoofer Right 2 Enter Audio Preset Memory mode Select “SOUND” > “PRESET” > “MEMO”. for how to select Function Control item , refer to <Function Control> (page 6). Turn the Control knob and push the center when the desired item is displayed. 3 Put the Audio Preset in the memory Press the Control knob. 3 Adjust the speaker Turn the Control knob. 4 Turn the Control knob to select “YES”, and then press the Control knob.  • When you select “USER” at <Preset position selection> (page 20), the adjusted setting value will be recalled. ⁄ • Register 1 pair of Audio Preset Memory. € When you press the Reset, all the sources will be the setting value which is registered. 8 8:46:13 PM Audio Adjustments Function of DPX503 Audio Control You can adjust following Audio Control items ; Adjustment Item Rear volume Subwoofer level* System Q* Display Range “REAR VOLUME” 0 — 35 “SUB-W LEVEL” –15 — +15 “NATURAL”/ Natural/User setting/Rock/ “USER”/“ROCK”/ Pops/Easy/Top 40/Jazz/Game “POPS”/“EASY”/ “TOP40”/“JAZZ”/ ”GAME” Bass level* “BASS LEVEL” –8 — +8 Middle level* “MIDDLE LEVEL” –8 — +8 Treble level* “TREBLE LEVEL” –8 — +8 Balance “BALANCE” Left 15 — Right 15 Fader “FADER” Rear 15 — Front 15 Exit Audio Control mode (Volume control mode) *Function of DPX303. [. . . ] € Media was played that does not have data recorded that the unit can play. 0 Maximum Supply current : 500 mA File System : FAT16/ 32 MP3 decode : Compliant with MPEG-1/2 Audio Layer-3 WMA decode : Compliant with Windows Media Audio AAC decode : AAC-LC “. M4a” files Audio section Maximum output power : 50 W x 4 Full Bandwidth Power (at less than 1% THD) : 22 W x 4 Speaker Impedance :4–8Ω Tone action Bass : 100 Hz ±8 dB Middle : 1 kHz ±8 dB Treble : 10 kHz ±8 dB Preout level / Load (CD) : 2500 mV/10 kΩ Preout impedance : ≤ 600 Ω AM tuner section Frequency range (10 kHz space) : 530 kHz – 1700 kHz Usable sensitivity (S/N = 20dB) : 28 dBμ (25 μV) CD player section Laser diode : GaAlAs Digital filter (D/A) : 8 Times Over Sampling D/A Converter : 24 Bit Spindle speed : 500 – 200 rpm (CLV) Wow & Flutter : Below Measurable Limit Frequency response (±1 dB) : 10 Hz – 20 kHz Total harmonic distortion (1 kHz) : 0. 008 % Signal to Noise ratio (1 kHz) : 105 dB Dynamic range : 93 dB MP3 decode : Compliant with MPEG-1/2 Audio Layer-3 WMA decode : Compliant with Windows Media Audio AAC decode : AAC-LC “. [. . . ]