User manual KENWOOD HM-337-SG

[. . . ] AC 230 V only Before applying power China and Russia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 V only Other countries . . . . . . . . . . . . . . . . . . . AC 110-120 / 220-240 V switchable* For the United Kingdom * AC voltage selection The AC voltage selector switches on the rear panel are set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting positions of these switches match your line voltage. [. . . ] ÷ When a key is held depressed, preset stations will be skipped at an interval of about 0. 5 second. ÷ To select a preset station from the remote, use the 4 P. CALL ¢ key or numeric keys. 20 EN Receiving Playback of TAPE broadcast station Collective presetting of stations AUTO MEMORY . . . . . For other countries Main unit only 1 Select the tuner input. TUNER/band 2 Select "AUTO MEMORY ?" (or "AUTO PRESET ?"). mode S S \ \ set/sound ÷ A maximum of 30 stations of the band presently being received will be preset. ÷ When there are many stations and the intended station has not been preset, please also use "One-by-one presetting (Manual preset)". Channel space setting (Except for U. S. A. , Canada, U. K. , Europe and Australia) The space between radio channels has been set to the one that prevails in the area to which the system is shipped. However, if the current channel space setting does not match the setting in the area where the system is to be used, for instance when you move from area 1 or area 2 shown in the following table or vice versa, proper reception of AM/ FM broadcasts cannot be expected. In this case, change the channel space setting in accordance with your area by referring to the following table. Main unit only 1 Turn power on. 2 While holding TUNER/band key pressed, turn the volume knob to select "FM 50 k" or "FM 100 k". Each turn switches the space frequency alternately. 1 FM 50 k 2 FM 100 k volume TUNER/band ÷ At FM 50 kHz, the corresponding AM frequency is 9 kHz. At FM 100 kHz, the corresponding AM frequency is 10 kHz. 3 Set it. set/sound Area 1 2 USA, Canada and South American countries Other countries CHANNEL Space Frequency FM: 100 kHz AM: 10 kHz FM: 50 kHz AM: 9 kHz 21 EN Receiving Playback of TAPE broadcast station Tuning to a non-preset radio station (Auto tuning, Manual tuning) Select the tuning mode according to the radio wave receiving condition. When the receiving condition is good: AUTO mode When it is poor due to weak radio waves: MANUAL mode ÷ In MANUAL mode, FM stations are received in monaural. 1 Select the AUTO or MANUAL mode. Each press alternates the mode. 1 "AUTO" : Stereo reception 2 "MANUAL" : Monaural reception ÷ Normally, use the AUTO (Auto tuning, stereo reception) mode. AUTO/MONO STOP 7 In AUTO mode : 2 Tune a station. To decrease frequency 1 TUNING 1 The next preset station can be received automatically every time the TUNING (1 or ¡) key is pressed. To increase frequency In MANUAL mode : Press the TUNING (1 or ¡) key repeatedly until the desired station is received. Check the tape transport direction indicator. * ÷ Search the position you want to start recording in advance. 26 EN Recording on TAPE mode \ 3. Set the recording condition. Select the reverse mode. ( set/sound Select an input source other than "TAPE" Example: To select the CD input CD rec Pause the recording rec ÷ Press the rec key during recording. It pause after leaving a non-recorded blank of 4 seconds. (Press the key again to resume recording. ) \ Lights ÷ Check the tape transport direction before starting recording. If it is set to the reverse direction, only one side of tape can be recorded regardless of the reverse mode setting made here. ÷ The tape equalizer is defeated during recording. 4. Select the source to be recorded. CD TUNER (Broadcasts) AUX (External input) [Adjusting the AUX input level fl] ÷ If a CD has already been loaded, it starts to play now. The character information display shows the recording input source. 5. 2 Play (or tune) the input source to be recorded. While recording an AM broadcast, beat sound can be minimised by switching the BEAT switch on the CD tray. BEAT 1 2 Select 1 or 2. ÷ Recording stops automatically when the tape side (s) to be recorded have been fully recorded. Stop the recording Tuning Mode time 27 EN Recording on TAPE Points in CD recording When recording CD tracks onto a tape, if you leave the cassette deck in record-pause mode beforehand, the cassette deck recording can be started when the CD starts to be played. 1 Put the CD player in pause mode. [. . . ] 1 Wow and flutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 2 % (W. R. M. S. ) Fast winding time . . . . . . . . . . . . . . . . . . . . . . . 100 seconds (C-60 tape) [General] Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 W Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]