User manual KENWOOD HM-636

[. . . ] COMPACT HI-FI COMPONENT SYSTEM HM-636 INSTRUCTION MANUAL KENWOOD CORPORATION B60-5377-00 00 MA (M, X, E) KW 0303 Before applying power Caution : Read this page carefully to ensure safe operation. Units are designed for operation as follows. and Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V only Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 240 V only Europe and U. K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ÷ No sound is heard while "PTY" is blinking. ÷ If a program of the desired type cannot be found, "NO PROG" is displayed, then after several seconds the display returns to the original display. ÷ If a program of the desired type is found, that program is received and the program type name display changes to the station name display. Goes off To change to a different program type : Repeat steps 1, 2, 3. Station name display. 25 EN Recording on TAPE Recording on TAPE The tape deck of the unit can record signals only on Normal (Type ) tapes. It cannot record on High (Type ) and Metal (Type ) tapes. Stop the recording Stop the recording Start recording/ Pause the recording 1. Load a tape in deck. 1 Press the area marked ) push open to open the cassette holder. 2 Insert a tape. 3 Press the area marked ) push open to close the cassette holder. Do not use a cassette with more than 90-minute recording time, for the tape used with such a cassette is very thin and tends to cause troubles such as entanglement around the pinch roller or cutting off tape. ÷ When there is a tape slack, wind the tape before loading. r 2. Select the tape transport direction. To reverse the transport direction : 1 Press the TAPE 2 3 key. 2 Stop playback. ÷ When recording is started, the tape is transported in the direction selected in this step. Check the tape transport direction indicator. * ÷ Search the position you want to start recording in advance. 26 EN Recording on TAPE \ 3. Set the recording condition. Select the reverse mode. ( Select an input source other than "TAPE" Example: To select the CD input Pause the recording ÷ Press the rec key during recording. It pause after leaving a non-recorded blank of 4 seconds. (Press the key again to resume recording. ) \ \ Lights ÷ Check the tape transport direction before starting recording. If it is set to the reverse direction, only one side of tape can be recorded regardless of the reverse mode setting made here. ÷ The tape equalizer is defeated during recording. 4. Select the source to be recorded. CD TUNER (Broadcasts) AUX (External input) [Adjusting the AUX input level fl] ÷ If a CD has already been loaded, it starts to play now. The character information display shows the recording input source. 5. 2 Play (or tune) the input source to be recorded. While recording from tuner input, beat sound can be minimised by pressing the set/demo key. Each press switches the modes as follows. [. . . ] 531 kHz ~ 1, 602 kHz (For Australia) Tuning frequency range . . . . . . . . . . 531 kHz ~ 1, 602 kHz (For other countries) Tuning frequency range 9 kHz step . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 kHz ~ 1, 602 kHz 10 kHz step . . . . . . . . . . . . . . . . . . . . . . . . . . 530 kHz ~ 1, 610 kHz Speakers (LS-M66) Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]