User manual KENWOOD KCA-HF521

[. . . ] Setting the Function Selecting the Preset Bands <When the KTC-V800N/V800P is connected> . Selecting the Seek Mode <When the KTC-V800N/V800P is connected> . Station Preset Memory <When the KTC-V800N/V800P is connected> . Selecting the Reception Area <When the KTC-V800P is connected> . [. . . ] [TINT] Press the [ 3 ] button for a stronger green level. Press the [ 2 ] button for a stronger red level. [COLOR] Press the [ 3 ] button for a deeper color. Press the [ 2 ] button for a paler color. [DIMMER] (for Night time screen) Press the [ 3 ] button for a brighter screen. Press the [ 2 ] button for a darker screen. [CONTRAST] Press the [ 3 ] button for stronger contrast. Press the [ 2 ] button for less contrast. [BLACK LEVEL] Press the [ 3 ] button for less black level. Press the [ 2 ] button for a stronger black level. NOTE SCREEN CONTROL BRIGHTNESS TINT COLOR DIMMER CONTRAST BLACK LEVEL + The [ TINT ] cannot be adjusted for the picture of PAL. The [ TINT ] and [ COLOR ] cannot be adjusted for the navigation picture. When the remote controllable distance becomes short, replace both of the batteries with new ones. Monitor Control Function V. SEL button Each time you press V. SEL button to switch the monitor's picture. MODE button Each time you press MODE button to switch the screen mode. AV OUT button Each time you press AV OUT button to switch the AV output mode. MODE V. SEL 4 CH. + TV Control Function BAND button Each time you press the BAND button, the preset band switches between the TV1 and TV2. SEARCH buttons Press the /CH. + button to make increasing seeks. SEEK button Each time you press the SEEK button, the seek mode switches to auto 1, to auto 2 and to manual. AME button You can automatically store all the receivable channels in the band currently being looked to. 5 SEEK AV OUT VOL AME SP REMOTE CONTROL UNIT RC-210 1 Select the band for auto memory entry. 3 Press the /CH. + button to start auto memory entry. 9 Installation Accessories English External view . . . . . . . . . Number of items External view . . . . . . . . . Number of items 1 . . . . . . . . 1 4 (4 x 12 mm) . . . . . . . . 5 2 . . . . . . . . 1 5 (4 x 16 mm) . . . . . . . . 2 3 . . . . . . . . 1 Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the terminal of the battery. [. . . ] A location which is not made of plastic. Do not install in locations where the entire support is at a diagonal such as in Figure B or where the monitor unit is facing down such as in Figure C. 2CAUTION Thoroughly wipe away and dust or grease from the installation location using a cloth which has been soaked in a neutral cleaning agent and wrung out. Attach the stand after allowing the installation location to dry. A ;;;;;;;;;;; ;;;;;;;;;;; ;;;;;;;;;;; ;;;;;;;;;;; ;;;;;;;;;;; ;;;;;;;;;;; ;;;;;;;;;;; ;;;;;;;;;;; ;;;;;;;;;;; ;;;;;;;;;;; B ;;;;;;;;; ;;;;;;;;; ;;;;;;;;; ;;;;;;;;; ;;;;;;;;; ;;;;;;;;; ;;;;;;;;; ;;;;;;;;; ;;;;;;;;; ;;;;;;;;; ;;;;;;;;; C ;;;;;;;; ;;;;;;;; ;;;;;;;; ;;;;;;;; ;;;;;;;; ;;;;;;;; ;;;;;;;; ;;;;;;;; ;;;;;;;; 1 Bend the stand support to conform to the shape of the installation location. 2 Adjust the shape of the support so that there is no rattling or gap when the stand is placed on the support. 3 Peel off the protective strip from the double-sided tape on the bottom of the stand and securely attach the stand. [. . . ]