User manual KENWOOD KCA-IP240V

[. . . ] · Check that no metal objects (coins, tools, etc. ) are left inside the unit to avoid short circuits. · If you smell or see smoke, turn the power off immediately and consult your Kenwood dealer. · Do not touch the liquid crystal fluid if the LCD is damaged or broken due to shock. The liquid crystal fluid may be dangerous to your health or even fatal. [. . . ] Display "SCROLL MANU" "SCROLL AUTO" Setting Doesn't scroll. Scrolls when the display changes. Modulation level Select the modulation level. Display "MOD LEVEL 1" "MOD LEVEL 2" (Initial setting) "MOD LEVEL 3" "MOD LEVEL 4" The texts scrolled are shown below. · CD text · Song title/ Artist name/ Album title/ Category name · MD title -- 13 -- Menu system English Sirius ID (ESN) <When the KTC-SR901 is connected> Sirius ID (Electronic Serial Number) is displayed. -- 14 -- Basic Operations of remote Loading and Replacing the battery Use two "AAA" batteries. Slide the cover while pressing downwards to remove it as illustrated. Insert the batteries with the + and ­ poles aligned properly, following the illustration inside the case. SRC SRC RDM button D. UP RDM REP D. DOWN CHSEARCH button + button - button T. DOWN D. REPEAT SCAN button button REP button 38/CH SEARCH button T. DOWN T. UP D. REPEAT T. UP button SCAN M. RDM button 1 2 M. RDM/DIRECT DIRECT button 2WARNING 3 4 5 6 Number 7 8 9 0 buttons Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed. · The provided batteries are intended for use in operation checking, and their service life may be short. · When the remote controllable distance becomes short, replace both of the batteries with new ones. · After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. · Insulate unconnected wires with vinyl tape or other similar material. · Some disc changers require optional equipment for connection. See the section on "Safety Precautions" for details. -- 17 -- Connecting Wires to Terminals English Display unit Control output Changer connection wire Control input CD/MD auto - changer input Output CD/MD auto-changer / Sirius satellite radio tuner O-N selection switch FM modulator unit FM/AM antenna input FM/AM antenna output Antenna plug for automobile "N" Car stereo with FM tuner Ignition key switch Ignition wire + (Red) ACC Battery wire + (Yellow) Car fuse box Ground wire (Black) - (To car chassis) Battery 2WARNING To prevent fire when the ignition wire (Red) or battery wire (Yellow) is short-circuited by coming into contact with the vehicle chassis (ground), only connect the power supply after making the fuse box connections. 2CAUTION Do not install an antenna of radio equipment or distribute the antenna wire near the changer output wire, for this could cause malfunction with this unit. Be sure to press the reset button after installation. -- 18 -- If you want to connect disc changers released in 1997 or earlier Display unit Control output Connection wire Control input "TO HEAD UNIT" CD/MD auto - changer input "TO CHANGER" FM modulator unit Sirius satellite radio tuner unit Connection wire ]"N" O N PROTOCOL SWITCH OFF ON AUX SWITCH AUX IN "TO HU" Output CD/MD auto-changer KCA-S210A Changer connection wire "TO CHANGER1" · Set the PROTOCOL selection switch to the "N" position. · The KCA-S210A must be connected to the Sirius satellite radio tuner unit if they are connected at the same time. · Up to two units of the Sirius satellite radio tuner unit or disc autochanger can be connected at the same time. -- 19 -- Installation English Installation of Display unit · Installation without using the trim mount plate 3 Display unit Installation of FM modulator unit 1 2CAUTION 2 Attach one strip of Velcro to the slanted-line of the the display units as shown to the left, and attach the other strip of Velcro to the parts where you wish to attach the display units. Then, put velcros together and install the display units. Take sufficient care so that the wires are not caught under the seat. If they are caught, they may break. 3 Install the FM modulator unit beneath the front seat using Metal fixture and Bind head screw as shown in the above figure. · Installation using the trim mount plate 3 Display unit 3 Pass the wire from the display unit through the hole on the trim mount plate and push fit the display unit into the trim mount plate until it locks. 2CAUTION · Be sure not to place the unit on such place as where it is exposed to direct sunlight and temperature eventually rises. It results in the deformation of the case. · Depending on the installing location, the display unit may not be able to receive the signals from the controller unit. Install them after confirming that the signals can be received. [. . . ] Do not use the ". MP3" extension in non-MP3. Takes time before the unit starts playing MP3. 71 The medium contains many discs, tracks, and hierarchical levels. The unit checks all tracks on the loaded medium first. If the medium has many tracks recorded, it may take a long time for the unit before it starts playing MP3. [. . . ]