User manual KENWOOD KDC-129S

[. . . ] CD-RECEIVER KDC-229 KDC-129 KDC-129S INSTRUCTION MANUAL © B64-2930-00/00 (MW) Contents Safety precautions Notes About CDs General features Power Selecting the Source Volume Attenuator System Q Audio Control Audio Setup Speaker Setting Clock Display Adjusting Clock Dimmer Control DSI (Disabled System Indicator) Theft Deterrent Faceplate TEL Mute 3 4 5 6 Accessories/ Installation Procedure14 Connecting Wires to Terminals Installation Removing the Unit Troubleshooting Guide Specifications 15 16 18 19 21 Tuner features Tuning Tuning Mode Station Preset Memory Auto Memory Entry Preset Tuning CRSC (Clean Reception System Circuit) Frequency Step Setting 10 CD player features Playing CD Fast Forwarding and Reversing Track Search Track Repeat Scan Play Random Play 12 2| English Safety precautions 2WARNING To prevent injury or fire, take the following precautions: · To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. Lens Fogging Right after you turn on the car heater in cold weather, dew or condensation may form on the lens in the CD player of the unit. Called lens fogging, CDs may be impossible to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer. 2CAUTION To prevent damage to the machine, take the following precautions: · Make sure to ground the unit to a negative 12V DC power supply. [. . . ] Manual -- Normal manual tuning control. 1 Select tuner source Press the [SRC] button. Select the "TUnE" display. 2 Select the band Push the Control knob to [FM] or [AM]. Each time the knob is pushed to [FM], it switches between the FM1, FM2, and FM3 bands. 3 Tune up or down band Push the Control knob to [4] or [¢]. · During reception of stereo stations the "ST" indicator is ON. 10 | English Station Preset Memory Putting the station in the memory. CRSC (Clean Reception System Circuit) Temporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. Press the [CRSC] button for at least 1 second. Each time the button is pressed, CRSC turns ON and OFF. When it's ON, "on CRSC" is displayed. 1 Select the band Push the Control knob to [FM] or [AM]. 2 Select the frequency to put in the memory Push the Control knob to [4] or [¢]. 3 Put the frequency in the memory Press the desired [1] -- [6] button for at least 2 seconds. The preset number display blinks 1 time. On each band, 1 station can be put in the memory on each [1] -- [6] button. Frequency Step Setting Changing the tuning frequency step. "SCN" indicator is ON. 2 Release it when the song you want to listen to is played Press the [SCAN] button. Random Play Playing all the songs on the disc in random order. Each time the button is pressed, Random Play turns ON and OFF. When it's ON, the "RDM" indicator is ON. · When the Control knob is pushed to [¢], the next song select starts. English | 13 Accessories/ Installation Procedure Accessories 1 . . . . . . . . . . 1 2 . . . . . . . . . . 2 3 . . . . . . . . . . 4 4 . . . . . . . . . . 4 5 . . . . . . . . . . 1 · If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chasis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. · If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. · If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. · If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with the same rating. · Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. · Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. · When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. [. . . ] No sound can be heard, or the volume is low. The fader or balance settings are set all the way to one side. The input/output wires or wiring harness are connected incorrectly. Reconnect the input/output wires or the wiring harness correctly. [. . . ]