User manual KENWOOD KDC-2018

[. . . ] In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer. 2CAUTION To prevent damage to the machine, take the following precautions: · Make sure to ground the unit to a negative 12V DC power supply. · Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. [. . . ] When a traffic information station is not being received the "TI" indicator blinks. When a traffic bulletin starts, "TRAFFIC" is displayed and the audio changes to traffic information. / · Traffic information can be switched when it is on the Tuner Source. Select another Program Type. 4 Exit PTY mode Press the Control knob. Program Type preset Putting the Program Type in the Preset button memory and quick recall. Presetting the Program Type 1 Select the Program Type to preset Refer to <PTY (Program Type)> (page 13). 2 Preset the Program Type Press the desired [1] -- [6] button for at least 2 seconds. Recalling the preset Program Type 1 Enter PTY mode Refer to <PTY (Program Type)> (page 13). 2 Recall the Program Type Press the desired [1] -- [6] button. English | 13 RDS features Changing Language for PTY Function Selecting the Program Type display language. 1 Enter PTY mode Refer to <PTY (Program Type)> (page 13). 2 Enter Changing Language mode Press the [TI] button. 3 Select the language Push the Control knob towards [FM] or [AM]. Each time you push the knob, the language alternates between the languages shown in the table below. Language English French German Display "ENGLISH" "FRENCH" "GERMAN" 4 Exit Changing Language mode Press the [TI] button. 14 | English CD player features Control knob IN indicator Track number Play time Playing CD When a disc is inserted Press the [SRC] button. Select the "CD" display. Fast Forwarding and Reversing Fast Forwarding Hold down toward [¢] with the Control knob. Reversing Hold down toward [4] with the Control knob. Release to resume the playback. / · When a CD is inserted, the "IN" indicator is ON. Pause and play Press the Control knob. Each time you press the knob, the audio pauses or plays. Eject the CD Press the [0] button. / · You can eject the disc for 10 minutes after switching off the engine. English | 15 CD player features Track Search Selecting the song you want to hear. Push the Control knob towards [4] or [¢]. Track Repeat Replaying the song you are listening to. Adjust the time manually. When you set "NEWS 00M" -- "NEWS 90M", the News Bulletin Interrupt function is ON. When the News Bulletin is ON, the "NEWS" indicator is ON. When the news bulletin starts, "NEWS" is displayed, and the tuner changes to the news bulletin. / · If you choose the "20MIN" setting, further news bulletins will not be received for 20 minutes once the first news bulletin is received. · The news bulletin volume is the same level that was set for <Traffic Information> (page 12). · This news bulletin function is only available if the desired station sends PTY-code for news bulletin or belongs to <Enhanced Other Network>-Network sending PTY-code for news bulletin. · When the News Bulletin Interrupt function is ON, the tuner changes to an FM station. / · It takes 3 to 4 minutes to synchronize the clock. In Standby mode DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display "DSI ON" "DSI OFF" Setting LED flashes. LED OFF. 18 | English In Tuner mode Local Seek Only stations whose reception is good are searched in auto seek tuning. Display "LO. S OFF" "LO. S ON" Setting The local seek function is OFF. The local seek function is ON. Restricting RDS Region (Region Restrict Function) You can choose whether or not to restrict the RDS channels, received with the AF function for a particular network, to a specific region. Display "REG ON" "REG OFF" Setting The Region Restrict Function is ON. [. . . ] Power control/ Motor antenna control wire (Blue/White) / To connect the Kenwood navigation system, consult your navigation manual. Battery wire (Yellow) Ignition wire (Red) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. / See next page. A-­7 Pin (Red) A­4 Pin (Yellow) Connector A Connector B 22 | English Connector Function Guide Pin Numbers for ISO Connectors External Power Connector A-4 A-5 A-7 A-8 Speaker Connector B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 Cable Colour Functions 2WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. [. . . ]