User manual KENWOOD KDC-3027

[. . . ] · If it doesn't seem to be working properly, first press the Reset button. If the malfunction persists, consult your Kenwood dealer. IMPORTANT INFORMATION · This unit is NOT designed to be connected directly to control units that are manufactured and sold before 1994. If used with such units, an optional CA-SD200 (sold separately) must be used. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO THIS UNIT AND CONTROL UNIT. [. . . ] The availability of this function as well as the number of discs which can be registered using this function and the number of usable characters may be variable depending on the control unit in use. Lens fogging · In cold climates, there may be a period after you turn on your vehicle's heater when the lens that guides the laser beam used in your CD player fogs up. If this happens, you cannot play compact discs. Take out discs and the fogging will disappear. If it does not return to normal after several hours, contact your Kenwood dealer. Heat protection · In warm climates, when vehicles are left standing in direct sunlight with the windows closed, the temperature inside can rise above 60°C. The unit's protection circuits will then display the message "HOLD" and prevent the player from operating. Just open the windows or turn on the air conditioning. As soon as the "HOLD" message disappears, the player will operate normally. 2 Handling compact discs Stains, scratches, or warping can cause skipping, malfunction, or low sound quality. Take the following precautions to avoid damage to the compact discs. · Avoid touching the recorded side (the side without the titles on) when you hold a compact disc. · Do not store discs where they will be exposed to direct sunlight (such as on the seat and dashboard) or high heat. · If you do not use your unit for an extended time, remove the discs from the unit and put them in their cases. If the door is not completely open, the magazine may hit the door and cause damage of malfunction. 4 Connections Changer control terminal 0 45 90 Control unit (optional) "O" "N" O-N D Changer control cable (5m) 2CAUTION · Do not connect the changer control cable while the control unit is turned ON. · Be sure to press the reset button after installation. · Do not install an antenna of radio equipment or distribute the antenna cable near the changer output cable, for this could cause malfunction with this unit. s Setting the O-N switch Set the O-N switch (lying to the right of the EJECT key) depending on the unit connected, as follows: Control unit Changer switching unit O-N switch setting CD text-capable None N KCA-S210A N Not CD text-capable None O KCA-S210A O KCA-S200 O · Consult the instruction manual for your control unit to check whether or not it is CD text capable. That information can be found on the page for External Disc Control in the section concerning switching to "N. " · In the "N"-operation mode, the disc titles and track titles provided by the CD text function can be displayed. (only KDC-C712/C662) 5 Installation s Accessories A×1 B×4 C×4 D×1 E×1 F×1 ' s Installation Procedure 1 Removing the transportation screws Remove all 3 transportation screws for protecting the internal mechanism before you start to install the unit. Transportation screws NOTE After removing the transport screw, retain it carefully and attach it again before transporting the unit again. 2 Angle adjustment switches · The angle adjustment switches on the both side of the unit are to be set according to the angle of installation of the CD auto changer. Set both of the two switches to the same position. If the switches are not set properly, sound skip or other malfunction may occur. [. . . ] If the switches are not set properly, sound skip or other malfunction may occur. · Set the angle adjustment switches with a coin or other flat object. · Change the switch step by step by detaching and reusing the object at the end of each step. 0 45 90 3 Cover the holes indicated by 3 with the dustproof seals E. (Bottom and sides) Use the holes marked q to install the unit. [. . . ]