User manual KENWOOD KDC-7007

[. . . ] In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. KENWOOD CORPORATION 2967-3, ISHIKAWA-CHO, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0. 21 CFR 1040. 10, CHAPTER 1, SUBCHAPTER J. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Turning Repeat Play On/Off: Press the REP button to switch repeat track/disc play on and off as follows: M Track Repeat ON M M Disc Repeat ON (Function of disc changers) Track/Disc Repeat OFF "Track Repeat/T-Repeat/Repeat ON" is displayed and the track number blinks in the display when track repeat is on. "Disc Repeat/D-Repeat ON" is displayed and the disc number blinks in the display when disc repeat is on. NOTE Disc Search (Function of disc changers) Search forward or backward through the discs in a disc changer. Making a Reverse Disc Search: Press the DISC­ button to display the desired disc number. Each time the button is pressed, the displayed disc number decreases by one. Play starts at the beginning of the displayed disc. Making a Forward Disc Search: Press the DISC+ button to display the desired disc number. Each time the button is pressed, the displayed disc number increases by one. Repeat play is canceled when you eject the disc. Track Scan Successively play the beginning of each track on a disc until you find the track that you want to listen to. Starting the Track Scan : Press the SCAN button. "Track Scan/Scan ON" is displayed and the first 10 seconds of each track will be played, in order. The track number currently being heard blinks in the display. Stopping to Listen to the Track Being Scanned: -- 26 -- Press the 38 or SCAN button again to stop the scan and keep on listening to a track normally. NOTE If you make no further input in the 10-second period, the number entry mode will automatically be canceled. Canceling Direct Track Search While It Is Operating: Press the 38 button. NOTE 2 Press either the 4 or ¢ button while the track number is · The track scan function is canceled when you eject the disc. Besides the alphabet (capital letters only) and numbers, you can choose the following characters: /, +, ­, , =, <, >, [ and ]. Direct Alphabet Input (KDC-X915/X815 only) (Function of remote with number/letter entry buttons) If the disc changers that were manufactured and sold after 1997 are connected (except for KDC-C560), you can directly input letters using the number/letter entry buttons on the remote. Example: Use the following table to enter the name "DANCE". Character Button to press # Times pressed NOTE 4 Each time the 38 button is pressed, the characters to be entered change as listed below. Press the DISC+ or DISC­ button to display the desired character. Characters that can be displayed are as follows. "D" "A" "N" "C" "E" the name. #3 #2 #6 #2 #3 1 1 2 3 2 5 Continue steps 3 and 4 until all the characters are chosen for -- 28 -- NOTE NOTE You can enter up to 10 characters for each name. 6 Press either the NAME. S button on the main unit or the OK button on the remote. The disc name is stored and the disc name preset mode is canceled. If you make no entry in a 10-second period, the name will be stored with the characters input so far. NOTE · The number of characters and discs whose names can be stored will differ depending on the disc changer that is connected. Please see your disc changer manual for details. · Discs are identified by their total length and number of tracks. If another disc happens to have the same specifications as one that you have already stored a name for, the name will be displayed for it, too. · If you want to change the name of a disc, repeat steps 1 and 2 to display the name, and then repeat steps 3 and 4 to input the changes. [. . . ] The specified disc does not play, but another one plays instead. No wire has been connected to the disc changer input terminal on the unit. The disc is loaded in a different slot from that specified. The disc is severely scratched. The sound skips. Something is touching the disc changer. The CD is scratched or dirty. The display shows that the changer is being played, but no sound can be heard. [. . . ]