User manual KENWOOD KDC-C20V

[. . . ] If the unit is installed at a dusty place, dust accumulates inside the unit and unit may be damaged. • When drilling a hole in the car to fix the brackets, make sure not to damage the fuel tank, brake tube, wiring harnesses, etc. • If the unit is installed near speakers, the speakers vibration may causes a sound skip. Install the unit as far away as possible from the speakers. • Be sure to use CDs with disc mark only for this unit. [. . . ] • Do not store discs where they will be exposed to direct sunlight (such as on the seat and dashboard) or high heat. A CD-R or CD-RW is more susceptible than a music CD to damage from high temperatures and humidity, and in some cases, may become unusable if left in the car for long periods of time. • If you do not use your unit for an extended time, remove the discs from the unit and put them in their cases. Do not leave them lying around without cases, piled up, or leaning on a wall and so on. • If you attach an adapter to an 8 cm (3") compact disc and load it into this unit, the adapter may be detached from the disc, causing damage to the unit. Do not use 8 cm (3") compact discs. Installation ■ Accessories A×2 B×4 C×4 D×1 E×1 F×1 G×1 ' ■ Removing the transportation screws Remove all 3 transportation screws for protecting the internal mechanism before you start to install the unit. NOTE After removing the transport screw, retain it carefully and attach it again before transporting the unit again. Transportation screws NTSC / PAL ■ Angle adjustment switches 45 0 Left side Angle adjustment switches S 90 0 45 90 Right side Installation angle V • The angle adjustment switches on the both side of the unit are to be set according to the angle of installation of the CD auto changer. Set both of the two switches to the same position. If the switches are not set properly, sound skip or other malfunction may occur. • Set the angle adjustment switches with a coin or other flat object. • Change the switch step by step by detaching and reusing the obdect at the end of each step. 40°~50° 85°~90° 0°~5° Angle adjustment switch position 90 45 0 45 90 0 45 90 0 It is not possible to install at an angle of 40°~50° if only A is used. 3 Installation Use the holes marked ● to install the unit. 2CAUTION Do not tighten the screw B too securely at the time of installation, but tighten it securely after having fixed the bracket A. English ■ Horizontal installation S 0 45 90 Angle adjustment switch position 45 90 0 V 45 90 0 C A 0 45 90 B Ø4 4 ■ Vertical installation S 0 45 90 Angle adjustment switch position 45 90 0 V 45 90 0 C 90 45 A 0 AUX OFF ON B Ø4 ■ In case of hanging in the trunk S Angle adjustment switch position 0 45 90 V 45 45 90 0 0 90 Ø4 A 0 45 90 B C 5 Connections O-N switch English "S" S 45 0 O C S T N / L A P N 45 90 0 V "V" D Changer control cable (5m) NTSC / PAL Changer control terminal "NTSC" "PAL" F Video cable (4m) Monitor unit (optional) Control unit (optional) Picture format selector switch EMultiple audio selector switch (5m) 2CAUTION • Do not connect the changer control cable while the control unit is turned ON. • Be sure to press the reset button after installation. • Do not install an antenna of radio equipment or distribute the antenna cable near the changer output cable, for this could cause malfunction with this unit. ■ Setting the O-N switch Set the O-N switch (lying to the right of the EJECT key) depending on the unit connected, as follows: Control unit Changer switching unit O-N switch setting CD text-capable None N KCA-S210A N Not CD text-capable None O KCA-S210A O KCA-S200 O Consult the instruction manual for your control unit to check whether or not it is CD text capable. That information can be found on the page for External Disc Control in the section concerning switching to "N. " ■ The picture format selector switch must be set to the format of the connected monitor. Set the KDC-C20V's picture format selector switch to "PAL" when a PAL monitor is connected, to "NTSC" when an NTSC monitor is connected. Use video CDs of the same format as the format to which the KDC-C20V is set. 2CAUTION • No picture will appear if the KDC-C20V's video output format is not the same as the monitor's picture format. • The top and bottom of the picture may be cut off or a black stripe may appear if the video CD's format is different from the KDC-C20V's video output format. ■ Multiple audio selector switch Connect the included multiple audio selector switch to the "S" (black) jack on the left side of the KDC-C20V. 6 Loading compact discs 1 ' 4 Projection ' Make sure the disc magazine is the right way up with the "disc" logo on the top. Pull the tray out by the projection. ' Insert the magazine into the CD changer until it clicks. 2 ' 5 Tray Close the CD changer door. NOTE Place the disc on the tray with the label facing upwards. [. . . ] • Set the angle adjustment switches to the correct positions. Press the reset button on the Control unit . Turn off the random play or magazine random play function. Set the O-N selection switch to "O" position. The picture and sound skips. [. . . ]