User manual KENWOOD KDC-C710

[. . . ] Detailed handling instructions will appear on the CD-R or CD-RW package: read this information carefully before using the disc. · Do not store discs where they will be exposed to direct sunlight (such as on the seat and dashboard) or high heat. A CD-R or CD-RW is more susceptible than a music CD to damage from high temperatures and humidity, and in some cases, may become unusable if left in the car for long periods of time. · If you do not use your unit for an extended time, remove the discs from the unit and put them in their cases. [. . . ] · If you attach an adapter to an 8 cm (3") compact disc and load it into this unit, the adapter may be detached from the disc, causing damage to the unit. Do not use 8 cm (3") compact discs. CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is using laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. 2WARNING Take the following precautions to prevent fire and avoid personal injury : · Check that no metal objects (coins, tools, etc. ) are left inside the unit to avoid short circuits. · If you smell or see smoke, turn the power off immediately and consult your Kenwood dealer. · Be sure to use CDs with disc mark only for this unit. · CD-Rs and CD-RWs which have not undergone finalization processing cannot be played. (For more information on finalization processing, refer to the manual for your CD-R/CD-RW writing software or CDR/CD-RW recorder. ) Additionally, depending on the recording status, it may prove impossible to play certain CDs recorded on CD-R or CD-RW. Do Not Use CDs with Sticker on the Labeled Side · Do not use the CD with the label sticker stuck on it. Using such a CD may cause the CD to be deformed and the sticker to peel off, resulting in malfunction of the unit. Connections Changer control terminal 2CAUTION Take the following precautions to keep the unit in proper working order. · Do not open the top or bottom cover. · Do not install the unit in places it is exposed to direct sunlight, high heat or humidity, water may splash over it, or dust exists. · Be sure to press the reset button after installation. · Do not install an antenna of radio equipment or distribute the antenna cable near the changer output cable, for this could cause malfunction with this unit. Setting the O-N switch Set the O-N switch (lying to the right of the EJECT key) depending on the unit connected, as follows: Control unit CD text-capable Not CD text-capable Changer switching None KCA-S210A None KCA-S210A KCA-S200 unit O-N switch setting N N O O O Consult the instruction manual for your control unit to check whether or not it is CD text capable. That information can be found on the page for External Disc Control in the section concerning switching to "N. " Loading compact discs 1 Projection ' Installation 4 Accessories A×1 B×4 C×4 D×1 E×1 ' ' Removing the transportation screws Make sure the disc magazine is the right way up with the "disc" logo on the top. Pull the tray out by the projection. ' Insert the magazine into the CD changer until it clicks. Remove all 3 transportation screws for protecting the internal mechanism before you start to install the unit. NOTE After removing the transport screw, retain it carefully and attach it again before transporting the unit again. Transportation screws 2 ' 5 Angle adjustment switches Tray Close the CD changer door. Left side Angle adjustment switches 45 90 0 0 45 90 NOTE Place the disc on the tray with the label facing upwards. Insert the tray into the disc magazine until it locks. Check that the discs and trays are inserted properly. The discs are numbered from the bottom from 1 to 6 or 10. 2CAUTION · Take care to insert trays into the correct grooves in the disc magazine and to insert discs properly into the tray grooves. [. . . ] 2CAUTION · Take care to insert trays into the correct grooves in the disc magazine and to insert discs properly into the tray grooves. Otherwise malfunction may occur or the disc may be damaged. · Insert all trays even when some of them do not carry discs. Otherwire malfunction or operation failure may occur. [. . . ]