User manual KENWOOD KDC-MPV5025 Instruction Manual

[. . . ] In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. KENWOOD CORPORATION 2967-3, ISHIKAWA-CHO, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0. 21 CFR 1040. 10, CHAPTER 1, SUBCHAPTER J. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Press once to fast forward to the next track, twice to fast forward to the track after that, and so forth. Play starts at the beginning of the displayed track number. NOTE (For disc changers) You cannot make a forward track search when listening to the last track on a disc. Play starts at the beginning of the displayed disc. NOTE "Load" is displayed when discs are being exchanged on the disc changer. Track / Disc Repeat Repeat playing the track or the disc currently being listened to. Turning Repeat Play On/Off: Press the REP button to switch repeat track/disc play on and off as follows: M Track Repeat ON M M Disc Repeat ON (Function of disc changers) Repeat OFF "Repeat ON" / "T-Repeat ON" is displayed and the track number blinks in the display when track repeat is on. "Disc Repeat ON" / "D-Repeat ON" is displayed and the disc number blinks in the display when disc repeat is on. NOTE Disc Search (Function of disc changers) Search forward or backward through the discs in a disc changer. Making a Reverse Disc Search: Press the DISC­ button to display the desired disc number. Each time the button is pressed, the displayed disc number decreases by one. Play starts at the beginning of the displayed disc. Making a Forward Disc Search: Press the DISC+ button to display the desired disc number. Each time the button is pressed, the displayed disc number increases by one. Repeat play is canceled when you eject the disc. Track Scan Successively play the beginning of each track on a disc until you find the track that you want to listen to. Starting the Track Scan: Press the SCAN button. "Scan ON" is displayed and the first 10 seconds of each track will be played, in order. Press the DISC+ or DISC­ button to display the desired character. Characters that can be displayed are as follows. Alphabet (upper case): A ~ Z Alphabet (lower case): a ~ z Numerals and symbols: 0~9 @ " ` ` % & +-=, . /\<>[] Disc Name Preset Play (DNPP) (Function of Remote) If you have preset the name of a disc that you want to listen to in the disc changer, you can look for it by name and start playing it. 1 Press the DNPP button on the remote. "DNPP" will appear in the display, and the disc name preset play mode is entered. The names of all the discs in the disc changer will appear successively in the display for five seconds each. Discs whose names have not been preset will appear as "NO NAME" in the display. NOTE Special characters: á à é è í ì ó ò ú ù Ñ Ç ® ß < fl â ä ê ëîïôöûüñç©Æ>fi 5 Continue steps 3 and 4 until all the characters are chosen for the name. NOTE You can enter up to 12 characters for each name. · This function can only be used in disc changers that were manufactured or sold as of 1997. Also note that some units -- 20 -- cannot provide a display unless the disc name preset has been made by the unit that is playing. · Discs in the disc changer that have never been played before will appear as "NO ACCESS" when the disc names are displayed. When you cannot identify a disc because of the "NO ACCESS" display after inserting a disc magazine, try playing it to display the disc name. Also note that "NO DISC" will be displayed when a disc has not been loaded. Rapid display (forward / reverse): Press the DISC+ or DISC­ button. Pressing the DISC+ button will rapidly display the preset names/disc titles in order. [. . . ] Cannot play CD-R or CD-RW. The computer chip in the unit is not functioning normally. Random play or magazine random play has been selected. The setting is not canceled. Turn off random play or magazine random play. The settings for these functions remain on until the setting to off or the disc ejected, even if the power is turned off or the source changed. Finalization processing is not being conducted for CDR/CD-RW. A non-compatible CD changer is being used to play the CD-R/CD-RW. Conduct finalization processing with CD recorder. [. . . ]