User manual KENWOOD KGC-4032

[. . . ] Also avoid places with too much dust or the possibility of water splashing. · Do not subject the faceplate to excessive shock, as it is a piece of precision equipment. · To prevent deterioration, do not touch the terminals of the unit or faceplate with your fingers. · When replacing a fuse, only use a new one with the prescribed rating. [. . . ] They can scratch the surface of the panel and/or cause the indicator letters to peel off. --3-- Buttons and Display English Release button 2 GRAPHIC EQUALIZER Equalizer operations KBS (Kenwood Built-in Sound) 3 SPEANA DEMO u S. A Four types of loudness levels and equalizer curves for rock, pops, vocal, and flat music genre have been preset. You can call up an equalizer curve for each genre at the touch of a button. Switching between KBS1, KBS2 and USER: KGC-4032 1 2 3 9 PATTERN SPECTRUM ANALYZER S. A 4V PREOUT EQ 1 Press the EQ button. 2 Each time you press the EQ button, the function changes from KBS1 to KBS2 to USER. 3 KBS1 3 KBS2 3 USER When KBS1 or KBS2 or USER is ON, the respective KBS1 or KBS2 or USER indicator lights. Selecting an equalizer curve preset in KBS1 or KBS2 or USER: Press any one of buttons 1 to 3. The selected curve is set and displayed, and the sound quality is changed accordingly. SUBWOOFER LEVEL ADJUSTABLE MENU 60 120 250 380 500 750 1k 2k 4k 8k 16k #1-3 d Title display EQ MENU MENU indicator DEMO indicator KBS indicator USER indicator No. indicator KBS / USER indicator "ROCK" "POPS" "VOCAL" NOTE "LOUD1" "LOUD2" "LOUD3" "PRESET1" "PRESET2" "PRESET3" Equalizer curve /Spectrum analyzer display ROCK: For rock sounds, POPS: For pops sounds, VOCAL: For vocal sounds, LOUD1-3: Loudness curves, PRESET1-3: User preset curves, Cancelling equlizer effects: Press the EQ button for more than one second to change the flat curves("FLAT"). --4-- Equalizer Adjustment You can adjust the sound level to suit your preference among 11 frequencies: 60 Hz, 120 Hz, 250 Hz, 380 Hz, 500 Hz, 750 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, and 16 kHz. Equalizer Curve Memory You can store four types of adjusted equalizer curves in memory, and can call up an original equalizer curve at the touch of a button. Selecting Band for Adjustment: Each time you press the 2 button, the band shifts to the left (lower frequencies), while each time you press the 3 button, the band shifts to the right (higher frequencies). 1 To adjust the sound quality to your preference. 2 Hold down any one of buttons 1 to 3 for more than 2 seconds. The adjusted equalizer curve will be stored in memory. NOTE Up to 3 equalizer curves can be stored in memory. Recalling Equalizer Curve from Memory: Increasing Level: Press the u button while the band indicator is blinking. The level can be adjusted up to +12 (by two steps). Decreasing Level: Press the d button while the band indicator is blinking. Connect the wiring harness cables in the following order: ground, battery. Connect the wiring harness connector to the unit. Press the reset button. 2CAUTION 1 . . . . . . . . . 1 2 . . . . . . . . . 2 3 . . . . . . . . . 1 2CAUTION 4 . . . . . . . . . 2 The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. · If the fuse blows, first make sure that the cables have not caused a short circuit, then replace the old fuse with one with the same rating. · Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits, also do not remove the caps on the ends of the unconnected cables or the terminals. · After the unit is installed, check whether the brake lamps, indicators, wipers, etc. · Insulate unconnected cables with vinyl tape or other similar material. · Some disc changers need conversion cables for connection. Before calling service, first check the following table for possible problems. English PROBLEM The power is not turned on. POSSIBLE CAUSE The fuse has blown. The power control cable are connected incorrectly. SOLUTION After checking for short circuits in the cables, replace the fuse with one having the same rating. [. . . ] Set the graphic equalizer level to a correct level. If the front and rear level gain is set to "HIGH", set the power amp input sensitivity to 4V. Match the main unit input sensitivity setting to the output voltage of the centre unit (see page 7). No sound can be heard, or the volume is low. The fader and/or balance settings are set all the way to one side. The input/output cables or wiring harness are connected incorrectly. [. . . ]