User manual KENWOOD KR-5200

[. . . ] In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-3609-00 00 CS MA (T, E2, Q) ID 99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3 2 Remote Control Other Operations Preparation Getting started 2 Before applying the power Units are designed for operation as follows. and Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V only Russia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2 Turn on the power to this receiver by pressing POWER and ON/ STANDBY keys. Selecting TAPE/MD Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source name associated with the MD/TAPE jacks to "MD, " follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". 2 Hold down the AUTO key for more than two seconds. · The source indication changes to "MD". · To return to the original indication, repeat the above procedure. · You also will need to change the name input to the remote control (RC-0507) to "MD". RC3 4 Input the distance to the speakers. 1 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to front speakers: ____ feets (meters) Distance to surround speakers: ____ feets (meters) 2 Use the MULTI CONTROL (TUNING/SKIP) to select the distance to the front speakers. The speaker indicator to be adjusted blinks. SP Selecting the speaker system Press the SPEAKERS A or B key to select the speaker system to be used. In this case, the input source is not switched. Selecting a source using the VIDEO key on the remote control (RC-R0507) 1 "VIDEO1" ("VCR1"*) 2 "VIDEO2" ("VCR2"*) 3 "DVD 6ch" 4 "<--->" (Not used by this receiver. ) · When selecting an input source by using the remote control (RCR0307), press the desired input selector key. · "VIDEO 2" can be selected as an input source only if the VIDEO 2/MONITOR setting is "VIDEO 2". 8 * Once setup codes are registered in the remote control (RCR0507), the input name display changes according to the name of the registered component. Example: if you register a VCR at the VIDEO 1 jacks, "VCR" appears instead of "VIDEO 1". RC2 · When using the remote control (RC-R0507) after initial setup, any inputs that have not been registered with a setup code are deleted from the cyclic list. RC4 · The INPUT SELECTOR on the front panel of the receiver always cycles through all inputs. Once-touch low frequency emphasis (bass boost) The following adjustments are possible if the receiver is in the stereo mode. · Press the key once to select the maximum (+10) low frequency emphasis setting. · This key does not function when the receiver is in the sound quality or ambience effects mode. 2 Start playback from the selected source. 3 Use the VOLUME CONTROL (VOLUME) to adjust the volume. Switching back to the previous setting Press the BASS BOOST key again. Operations Adjusting the tone Normal playback Recording KR-5200/V6010/V5010 (En/T) 16 Muting the sound MUTE lets you mute the sound of the speakers. Press the MUTE key. SP Recording audio VIDEO 2 / MONITOR A MUTE L R SW Blinks CD Recording a music source INPUT SELECTOR · On the KRF-V5010, this selection can be made using the control on the receiver as well. To cancel Press the MUTE key again so that the "MUTE" indicator goes off. · Muting can also be cancelled by adjusting the volume. When recording a music source, switch the VIDEO2/MONITOR setting to "MONITOR". [. . . ] 87. 5 MHz ~ 108 MHz, 65. 0 MHz ~ 74. 0 MHz Usable sensitivity (DIN, 75 ) MONO . . . . . . . . . . . . . . . . . . . . 1. 2 µV / 13. 2 dBf (40 kHz DEV. , S/N 26 dB) STEREO . . . . . . . . . . . . . . . . . . 35 µV / 42. 1 dBf (46 kHz DEV. , S/N 46 dB) Total harmonic distortion (DIN, 1 kHz) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 2% (65. 2 dBf input) STEREO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]