User manual KENWOOD KRC-165

[. . . ] · Do not open the top or bottom covers of the unit. · Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. · Do not subject the faceplate to excessive shock, as it is a piece of precision equipment. [. . . ] · Adjusting the minutes Press the ¢ button to advance the minutes, or press the 4 button to make the minutes go back. 1 Press the AUD button to enter the Sound Coordinate mode. 2 Press a preset button (#1-5). The preset settings of the bass and treble tones are recalled. #1: Flat (dB-1) #2: Rock (dB-2) #3: Pops/Top 40 (dB-3) #4: Jazz (dB-4) #5: Easy (dB-5) 4 Press the CLK button to end the clock adjustment mode. 3 Press the AUD button to end the sound coordinate mode. NOTE You can call the following settings with this function; bass center frequency, bass level, bass quality factor, bass extension, treble center frequency, and treble level setting. Clock display Turning clock display On/Off: Each time you press the CLK button, the display switches between the clock and each mode display. --6-- Tuner features Tuning You can choose between auto seek tuning of receivable frequencies and manual tuning. 1 Press the SRC (source) button repeatedly to select the tuner mode. "TUnE" is displayed when the tuner mode has been selected. KRC-165 2 Press the BAND button to select the band. Each time you press the BAND button, the band switches between FM1, FM2, FM3, and AM. 3 Press the AUTO button to switch between auto seek tuning and manual tuning. The AUTO indicator lights up only when auto seek tuning is selected. 4 · Auto Seek Tuning Press the ¢ button Press the 4 button · Manual Tuning Press the ¢ button Press the 4 button to seek higher frequencies. to decrease the frequency by one step. NOTE Band display Frequency Preset station number The STEREO indicator lights up when stereo broadcasts are being received. indicator AUTO indicator STEREO indicator --7-- Tuner features English Station Preset Memory Store the frequency of a station. You can then recall that station with a single touch of a button. Frequency Step Setting Switch the frequency step used in seeks. The factory defaults are 50 kHz for FM and 9 kHz for AM. 1 Select the band/ station that you want to have stored. 2 Press the button (#1-6) that you want to use for the station, for at least two seconds. The button number blinks once in the display to indicate that the data has been stored. Recalling a Preset Station: Press the preset station button (#1-6) for the desired station. The number of the recalled station is displayed. NOTE 1 Turn the power off. 2 Hold down buttons #1 and #5, then turn the power back on. The frequency step settings will be changed to 200 kHz for FM and 10 kHz for AM. NOTE When you change the frequency step settings, all memory contents will be erased. Returning Frequency Step Settings to Original Values: Repeat steps 1 and 2 above. You can store six stations in each of the FM1, FM2, FM3, and AM bands. Clean (CRSC Reception System Circuit) Auto Memory Entry You can automatically store all the receivable frequencies in the band currently being listened to, and then recall them with the touch of a button later. This function is especially useful when you are travelling and do not know what stations are available. Up to six frequencies can be stored this way. The tape indicator blinks in the direction of the tape as it is being rewound. If the FF button is pressed, normal tape play will begin. T. CALL indicator Tape indicator --9-- Cassette player features English Tuner Call Switch automatically to the tuner while you are rewinding or fast forwarding the tape. Turning Tuner Call On/Off: Press the T. CALL button to switch tuner call on and off. The T. CALL indicator lights up when tuner call is turned on. NOTE When you turn on the Tuner Call function, the motorised antenna will extend automatically. -- 10 -- Accessories External view 1 Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. Make the proper input and output wire connections for each unit. Connect the speaker wires of the wiring harness. [. . . ] Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". Radio reception is poor. The car antenna is not extended. The antenna control wire is not connected. The memory is erased when the ignition is turned off. The battery wire has not been connected to the proper terminal. [. . . ]