User manual KENWOOD KRC-803 SERVICE MANUAL

[. . . ] Otherwise it may fall out of place when jolted. · When extending the ignition, battery, or ground wires, make sure to use automotivegrade wires or other wires with a 0. 75mm2 (AWG18) or more to prevent wire deterioration and damage to the wire coating. · To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. · If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. [. . . ] Use this mode when you want to have the display illuminated but don't want to listen to anything. NOTE The mode switches to the next mode from any mode which cannot be used. ATT indicator LOUD indicator --5-- General features English Volume Increasing Volume: Press the u button to turn up the volume. Decreasing Volume: Press the d button to turn down the volume. 1 Press the AUD button for at least one second to enter the control mode. 2 Selecting mode Press either the BAND button. Each time the button is pressed, the adjustment mode will change. Please refer to the following for the contents of the adjustment modes. NOTE Source tone memory Each source ( tape, FM and AM ) has its own memory in which to store the bass and treble tone settings. The settings made for a particular source are recalled automatically whenever you use that source ( for example, FM mode uses the tone settings made for FM, AM for AM, etc. ). Attenuator This function allows you to turn down the volume quickly. Turning Attenuator On/Off: Press the ATT button to switch the attenuator on and off. When the attenuator is on, the ATT indicator blinks. When the attenuator is off, the volume returns to the original level. NOTE 3 Adjust each mode Press the 4/¢ button. Please refer to the following for the adjusting values. Turning the volume up, or turning it all the way down deactivates the attenuator function. 4 Press the AUD button to end the control mode. Loudness This function amplifies low and high tones when the volume is turned down. The LOUD indicator lights up when the loudness function is on. Turning Loudness On/Off: Press the LOUD button for at least one second to switch the loudness on and off. "BAS": Adjust the bass level. The number of the recalled station is displayed. Clean Reception System Circuit (CRSC) Temporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. The factory default for this function is ON. Turning CRSC On/Off: Press the CRSC button for at least one second to turn the function on/off. The indicator lights up when CRSC is on. NOTE Strong electrical fields (such as from power lines) may cause --9-- Cassette player features English Playing Cassette Tapes SRC / PWR OFF 0 REW FF KRC-803 T. CALL Loading and Playing Cassettes: Load a cassette with the tape exposed on the right. With side A facing up, the 3 indicator lights up when side A is playing, and 2 when side B is playing. The 2 3 indicator lights up while play is paused. Playing Cassettes Already Loaded: Press the SRC (source) button repeatedly to select the tape mode. "TAPE" is displayed when the tape mode has been selected. Listening to the other side: Press the FF button and REW button at the same time. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. · If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. [. . . ] 15)" and then remove the hard rubber frame. English Firewall or metal support 2 Align the holes in the unit (two locations on each side) with the Accessory4 vehicle mounting bracket and secure the unit with the accessory screws. T N Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. 8mm MAX. T T/N ø5mm 5 ø5mm 6 T: Toyota cars N: Nissan cars 2CAUTION Accessory5. . . for Nissan car Accessory6 . . . for Toyota car Self-tapping screw (commerciall y available) NOTE Accessory2 Metal mounting strap Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). · During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. [. . . ]