User manual KENWOOD KRF-V4550D

[. . . ] AUDIO VIDEO SURROUND RECEIVER Preparations Additional Information Operations KRF-V4550D INSTRUCTION MANUAL KENWOOD CORPORATION B60-4967-EN Before applying the power Units are designed for operation as follows. Caution : Read this page carefully to ensure safe operation. 2 Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. [. . . ] · You can store a separate input level for each input source. If the MONITOR function is on, you can store an input level for when MONITOR is on independently of the input levels for the input sources. 2 Press the SOUND key several times until the "INPUT" indication appears. 3 Use the MULTI CONTROL to adjust the input level. SP B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS The speaker indicator lights. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS L LFE C S R SW LS RS Press the SPEAKER key to switch the speakers on and off. Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER and ON/ STANDBY keys. L LFE C S R SW LS RS AUTO FM AUTO SOUND DIGITAL AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED DSP kHz DOWN MIX · The adjustment mode is displayed for approximately eight seconds. · The input level may be adjusted to any one of three settings: 0, -3, and -6. (The initial setting is 0. ) 4 Press the SOUND key to return to the input indication. Operations Normal playback 18 Listening to a source component VOLUME CONTROL INPUT SELECTOR Adjusting the sound MULTI CONTROL SOURCE DIRECT SOUND PHONES MUTE VOLUME CONTROL SPEAKER INPUT SELECTOR VOLUME SOUND MULTI CONTROL BASS BOOST MUTE 1 Use the INPUT SELECTOR to select the source you want to listen to. The input sources change as shown below: VOLUME Adjusting the tone You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 Press the SOUND key to select the tone mode to be adjusted. BASS: Select this to adjust the low frequency range. (Press the SOUND key once. ) TREB: Select this to adjust the high frequency range. (Press the SOUND key twice. ) SP B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS Operations Selecting a source using the INPUT SELECTOR knob 1 2 3 4 5 6 7 "PHONO" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" "VIDEO2" "DVD/6ch" L LFE C S R SW 2 Start playback from the selected source. 3 Use the VOLUME CONTROL knob (VOLUME keys) to adjust the volume. LS RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP 2 Use the MULTI CONTROL to adjust the sound quality. · The bass and treble levels are adjustable from -10 to +10 in 2 step increments. · The adjustment item is displayed for approximately 8 seconds. Selecting VIDEO 2/MONITOR Depending on the component connected to the VIDEO 2/MONITOR jacks, select either the "VIDEO 2" setting or the "MONITOR" setting, as appropriate. 7 Once-touch low frequency emphasis (bass boost) You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. · Press the key once to select the maximum (+10) low frequency emphasis setting. · This key does not function when the receiver is in the sound quality or ambience effects adjustment mode. Switching back to the previous setting Press the BASS BOOST key again. Normal playback Recording Recording audio (analog sources) MONITOR Muting the sound The MUTE key lets you mute the sound of the speakers. Press the MUTE key. SP B TI. VOL MUTE CLIP RDS EON PTY TP TA NEWS 19 L LFE C S R SW LS RS Blinks To cancel Press the MUTE key again so that the "MUTE" indicator goes off. · Muting can also be canceled by adjusting the volume. INPUT SELECTOR Recording a music source When recording a music source, switch the VIDEO2/MONITOR setting to "MONITOR" . 7 1 Use the INPUT SELECTOR knob to select the source (other than "MD/TAPE") you want to record. [. . . ] 87. 5 MHz ~ 108 MHz Usable sensitivity (DIN at 75 ) MONO . . . . . . . . . . . . . . . . . . . . . . . . S/N 26 dB) STEREO . . . . . . . . . . . . . . . . . . . . . . S/N 46 dB) Total harmonic distortion (1 kHz) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 2% (71. 2 dBf input) STEREO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]