User manual KENWOOD KRF-V5090D

[. . . ] If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future. Keep this manual handy for future reference. U. K. [. . . ] TUNED kHz DOWN MIX DSP KRF-V7030D/V6030D KRF-V5030D/V4530D · The adjustment mode is displayed for approximately eight seconds. · The input level may be adjusted to any one of three settings: 0, -3, and -6. (The initial setting is 0. ) 4 Press the SOUND key to return to the input indication. · Activating a surround mode or selecting "DVD/6ch" as the input source causes speaker system A to be selected automatically. On the KRF-V5030D/V4530D, press the SPEAKER key to switch the speakers on and off. Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER and ON/ STANDBY keys. Normal playback Listening to a source component VOLUME CONTROL INPUT SELECTOR Adjusting the sound MULTI CONTROL KRF-V6030D/ V5030D/ V4530D 17 SOURCE DIRECT SOUND SPEAKERS A/B PHONES VOLUME CONTROL INPUT SELECTOR VOLUME RC-R0610 INPUT SELECTOR VOLUME RC-R0510 SOUND MULTI CONTROL B. BOOST MUTE SOUND MULTI CONTROL BASS BOOST MUTE VOLUME RC-R0610 RC-R0510 1 Use the INPUT SELECTOR to select the source you want to listen to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob VOLUME Adjusting the tone Operations You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 Press the SOUND key to select the tone mode to be adjusted. BASS: Select this to adjust the low frequency range. (Press the SOUND key once. ) TREB: Select this to adjust the high frequency range. (Press the SOUND key twice. ) SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS KRF-V7030D 1 2 3 4 5 6 7 8 9 "PHONO" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" "VIDEO2" "VIDEO3" "DVD/6ch" "AV AUX" L LFE C S R SW LS RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP KRF-V6030D/V5030D/V4530D 1 2 3 4 5 6 7 "PHONO" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" "VIDEO2" "DVD/6ch" 2 Use the MULTI CONTROL to adjust the sound quality. · The bass and treble levels are adjustable from -10 to +10 in 2 step increments. Alternately, if a cassette deck equipped with a 3-head system is connected to the VIDEO2/ MONITOR jacks, you will be able to monitor the just-recorded signal while making recordings on the cassette deck. By switching the MONITOR key on and off, you can compare the sound of the source signal and the just-recorded signal. For more information, refer to the instruction manual of the connected component. 3 Use the VOLUME CONTROL (VOLUME) to adjust the volume. Recording Recording video 1 Use the INPUT SELECTOR to select the video source (other than "VIDEO1") you want to record. 2 Set the video deck connected to VIDEO 1 to record. · Select the REC MODE to record a digital input source. · With certain video software, recording may not be normal due to the copy guard condition. · Recording music in M-REC MODE DIMMER 19 Recording audio (digital sources) Switch on the REC MODE to record a digital input source. Usually use the A-REC MODE to record audio input sources. When the digital mode changes during recording in the A- REC MODE, the audio may be interrupted momentarily. To record the audio from the beginning of the digital mode change, use the M-REC MODE. With a model that is not compatible with DTS, no audio is reproduced even when the DTS signals are input. INPUT SELECTOR 1 Use the input selector to select the source (CD, DVD, VIDEO2, or VIDEO3) you want to record. [. . . ] · An attempt is made to play a tape which is being recorded in the cassette deck. · The remote control has not been set to the operation mode for the component you wish to control. · The microprocessor of the remote control malfunctions. Remedy · Register a setup code at the respective input(s). [. . . ]