User manual KENWOOD KRF-V6030

[. . . ] Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-4947-00 00 MA (E2, T) PR 0009 Additional Information Remote Control Operations Preparations Before applying the power Units are designed for operation as follows. Caution : Read this page carefully to ensure safe operation. 2 Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. [. . . ] 3 Use the MULTI CONTROL keys to adjust the input level. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS The speaker indicator lights. SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS L LFE C S R SW L LFE C S R SW LS RS LS RS KRF-V6050D KRF-V6030 · Selecting "6ch INPT" by pressing the INPUT MODE key, whereby "DVD/6ch" is the input source, will cause SPEAKER A to be selected automatically. On the KRF-V6030, press the SPEAKER key to switch the speakers on and off. L LFE C S R SW LS RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO STEREO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP · The adjustment mode is displayed for approximately eight seconds. · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER (and ON/ STANDBY) keys. Operations SW 1 Use the INPUT SELECTOR knob to select "TAPE". Normal playback 20 Listening to a source component VOLUME CONTROL INPUT SELECTOR Adjusting the sound MULTI CONTROL SOURCE DIRECT SOUND SPEAKERS A/B PHONES VOLUME CONTROL INPUT SELECTOR VOLUME RC-R0616 RC-R0512 RC-R0616 SOUND MULTI CONTROL B. BOOST/ BASS BOOST MUTE VOLUME RC-R0512 1 Use the INPUT SELECTOR to select the source you want to listen to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob. Adjusting the tone You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 Press the SOUND key to select the tone mode to be adjusted. BASS: Select this to adjust the low frequency range. (Press the SOUND key once. ) TREB: Select this to adjust the high frequency range. (Press the SOUND key twice. ) SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS Operations KRF-V6050D 1 2 3 4 5 6 7 8 6 7 "PHONO" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" if VIDEO2/MONITOR is VIDEO2 "VIDEO2" "DVD/6ch" "AV AUX" else if VIDEO2/MONITOR is MONITOR "DVD/6ch" "AV AUX" L LFE C S R SW LS RS FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP 2 Use the MULTI CONTROL keys to adjust the sound quality. · To copy tapes using a double cassette deck, refer to the instruction manual of the double cassette deck. Make sure the SP indicators are turned off. R SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS L LFE C S L LFE C S R SW SW LS RS LS RS KRF-V6050D KRF-V6030 · If you turn off all of the speakers when in the surround mode, the surround mode will be canceled as well, resulting in stereo playback. 2 Connect the headphones to the PHONES jack. PHONES MONITOR function (analog sources only) You can connect a cassette deck or graphic equalizer to the VIDEO2/ MONITOR jacks of the receiver. If a graphic equalizer is connected, the MONITOR key should be left in the on position. Alternately, if a cassette deck equipped with a 3-head system is connected to the VIDEO2/ MONITOR jacks, you will be able to monitor the just-recorded signal while making recordings on the cassette deck. By switching the MONITOR key on and off, you can compare the sound of the source signal and the just-recorded signal. For more information, refer to the instruction manual of the connected component. 3 Use the VOLUME CONTROL knob (VOLUME keys) to adjust the volume. Operations · When you press the LISTEN MODE, SOUND, or SET UP keys, or switch to another input source, SOURCE DIRECT playback will be canceled. Recording tapes or MD (with MONITOR function) When recording a music source, switch the VIDEO2/MONITOR setting to "MONITOR". 8 Recording 22 Recording video For A-REC mode: 1 Use the INPUT SELECTOR to select the video source (other than "VIDEO1") you want to record. 2 Set the video deck connected to VIDEO 1 to record. · Select the REC MODE to record a digital input source. · Recording may not be normal for some video software. This is due to the copy guard condition. [. . . ] at 6 , one channel driven) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . at 6 , one channel driven) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 W + 100 W Total harmonic distortion . . . . . . . . . . . . . . . . . . . . . . . . . 0. 050% (1 kHz, 50W, 6 ) Frequency response (IHF '66) CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]