User manual KENWOOD KRF-V6060D

[. . . ] AUDIO VIDEO SURROUND RECEIVER KRF-V7060D KRF-V6060D VR-6050 INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is for some models. Model availability and features (functions) may differ depending on the country and sales area. About the supplied remote control Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). [. . . ] · SPEAKER EQ cannot be turned OFF when ACTIVE EQ is turned ON. · SPEAKER EQ function will not be available when REC MODE, AUTO TUNING or PRESET MEMORY is ON, and during 96kHz LPCM playback. 1 SPEAKER EQ SMALL 3 When in TONE ON selection, press the TONE key for the following displays. BASS : Select this to adjust the low frequency range. TREBLE : Select this to adjust the high frequency range. 4 Use the MULTI CONTROL knob or Joystick (5/) to adjust the sound quality. SP L C SW R LFE AB MUTE CLIP COAXIAL DTS. DOLBY DIGITAL STEREO OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. MATRIX DSP MODE DISCRETE PRO LOGIC LOUDNESS ANALOG 96kHzfs NEO:6 CSII THX Surround EX RDS RTY AUTO MEMO STEREO TUNED SL S SB SR · The bass and treble levels are adjustable from -10 to +10 in 2 step increments. · The adjustment item is displayed for approximately 8 seconds. Once-touch low frequency emphasis (BASS BOOST) (remote control only) You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo modes. · Press the key once to select the maximum (+10) low frequency emphasis setting. · This key does not function when the receiver is in the sound quality or ambience effects adjustment mode. Listening with headphones 1 Press the A and B Speaker keys so that the speaker indicator goes off. Make sure the SPEAKERS indicators are turned off. SP AB LFE MUTE CLIP COAXIAL OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DSP MODE D ANALOG 96kHzfs Switching back to the previous setting Press the BASS BOOST key again. SL S SB SR · If you turn off all of the speakers when in surround mode, the surround mode will be canceled as well, resulting in stereo playback. 2 Connect headphones to the PHONES jack. PHONES Adjusting the LOUDNESS mode You can adjust the Loudness function which controls the low volume settings to maintain the music's richness. The adjustment can be made when the receiver is in the PCM stereo and analog stereo mode. Press the LOUDNESS key to turn the LOUDNESS setting ON. To cancel Press the LOUDNESS key again so that the "LOUDNESS" indicator goes off. 3 Use the VOLUME CONTROL knob or VOLUME +/­ keys to adjust the volume. 22 EN Recording Recording audio (analog sources) 3 Press and hold the DIMMER key for more than 2 seconds to select the AUTO REC or MANUAL REC mode. 1 REC MODE off : The digital input record mode is switched off. 2 AUTO REC mode : The digital input signals (DTS, Dolby Digital, or PCM) are identified automatically and converted into stereo signals that are ready for recording. 3 MANUAL REC mode : The input signal type at the moment this mode is selected is held throughout this mode. MD/TAPE Recording a music source 1 Use the Input Selector keys to select the source (other than "MD/ TAPE") you want to record. 2 Set the MD or TAPE recorder to record. For AUTO REC mode : SP L C SW R LFE AB MUTE CLIP COAXIAL DTS. [. . . ] 87. 5 MHz ~ 108 MHz Usable sensitivity MONO . . . . . . . . . . . . 1. 3 µV (75 )/ 13. 2 dBf (40 kHz dev, S/N 26 dB) STEREO . . . . 45 µV (75 )/ 42. 1 dBf (40 + 6 kHz dev, S/N 46 dB) Total harmonic distortion MONO (1 kHz, 40 kHz dev) . . . . . . . . . . . . . . . . . . . . . . . 0. 2% (65. 2 dBf input) STEREO (1 kHz, 40 + 6 kHz dev) . . . . . . . . . . . . . . . [. . . ]