User manual KENWOOD KRF-V7020

[. . . ] KRF-V7020/V6020/V5020 (En/T) 1 AUDIO VIDEO SURROUND RECEIVER KRF-V7020 KRF-V6020 KRF-V5020 INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is for some models. Model availability and features (functions) may differ depending on the country and sales area. About the supplied remote control (RC-R0508) . . Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. [. . . ] 2 Hold down the AUTO key for more than two seconds. · The source indication changes to "MD". · To return to the original indication, repeat the above procedure. · You also will need to change the name input to the remote control (RC-0508) to "MD". RC3 4 Input the distance to the speakers. 1 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to front speakers: ____ feet (meters) Distance to surround speakers: ____ feet (meters) 2 Use the MULTI CONTROL (TUNING/SKIP) to select the distance to the front speakers. The speaker indicator to be adjusted blinks. SP Selecting the speaker system Press the SPEAKERS A or B key to select the speaker system to be used. : Sound from the speakers connected to the SPEAKERS A terminals on the rear panel. B ON : Sound from the speakers connected to the SPEAKERS B terminals on the rear panel. A+B ON : Sound from both the speakers connected to the SPEAKERS A and B terminals on the rear panel. Use this setting when listening with headphones for stereo sound in all playback modes. A ON · Activating a surround mode or selecting "DVD 6ch" as the input source causes speaker system A to be selected automatically. On the KRF-V5020, press the SPEAKERS key to switch the speakers on and off. A L R Indication in feet 1)FT 3. )M Indication in meters · The allowable setting range is 1 to 30 feet (0. 3 to 9. 0 m), adjustable in 1 foot (0. 3 m) increments. 4 Repeat steps 2 and 3 to input the distance for the surround speaker. 5 Setup is complete when the input indication reappears. L R SW Display when all speakers have been selected. · The speakers you selected appear on the display. Confirm that all the speakers have been correctly selected. CD The indicator for the speakers you want to use should be lit. SP Speaker indicator lights. SP AB L R SW L R SW · If you used the remote control (RC-R0508) to perform the settings, press the VIDEO key at this point to turn off the remote control's own adjustment mode. In this case, the input source is not switched. Models other than KRF-V5020 KRF-V5020 Selecting VIDEO 2/MONITOR Depending on the component connected to the VIDEO 2/MONITOR jacks, select either the "VIDEO 2" setting or the "MONITOR" setting, as appropriate. 8 Normal playback KRF-V7020/V6020/V5020 (En/T) Listening to a source component VOLUME CONTROL INPUT SELECTOR Adjusting the sound SOURCE DIRECT BASS BOOST SOUND VOLUME CONTROL 15 VIDEO AUDIO VOLUME VOLUME Input selector keys RC-R0508 RC-R0710 MULTI CONTROL PHONES SPEAKERS A/B SPEAKERS, MUTE (KRF-V5020) VIDEO VOLUME TUNING/SKIP MUTE SOUND VOLUME MUTE SOUND MULTI CONTROL 1 Use the input selector (INPUT SELECTOR (AUDIO, VIDEO)) to select the source you want to listen to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob 1 2 3 4 5 6 7 TUNER "CD" ("CD"*) "TAPE" or "MD" ("TAPE"*) "PHONO"("PHONO"*) "VIDEO1" ("VCR1"*) "VIDEO2" ("VCR2"*) "DVD 6ch" RC-R0508 RC-R0710 The following adjustments are possible if the receiver is in the stereo mode. 1 Press the SOUND key to select the tone mode to be adjusted. BASS: Select (Press TREB: Select (Press SP this to adjust the low frequency range. [. . . ] 1. 2 µV / 13. 2 dBf (40 kHz DEV. , S/N 26 dB) STEREO . . . . . . . . . . . . . . . . . . 45 µV / 44. 2 dBf (46 kHz DEV. , S/N 46 dB) Total harmonic distortion (DIN, 1 kHz) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 2% (65. 2 dBf input) STEREO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 8% (65. 2 dBf input) Signal to noise ratio (DIN weighted, 1 kHz) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]