User manual KENWOOD KRF-V8090D

[. . . ] AUDIO VIDEO SURROUND RECEIVER KRF-V8090D INSTRUCTION MANUAL About the supplied remote control Compared to standard remote controls, the remote control supplied with this model has several operation modes. These modes enable the remote control unit to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-5556-10 01 CS (E, X) OC 0504 Before applying the power Units are designed for operation as follows. [. . . ] • Turn on SPEAKERS A if using SUBWOOFER PRE OUT terminal to output sound. 24 EN *5556/24-31/EN 24 05. 7. 6, 0:21 PM Normal playback Input level adjustment (analog sources only) MULTI CONTROL Adjusting the sound ACTIVE EQ LOUDNESS TONE MULTI CONTROL SOUND INPUT SELECTOR PHONES BASS BOOST VOLUME CONTROL TONE MUTE LOUDNESS VOLUME%/fi MULTI %/ fi, @/# Input Selector keys SOUND BASS BOOST MULTI %/ fi RCV MODE RCV MODE ACTIVE EQ ACTIVE EQ mode Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink. Adjust the input level. SP L C LFE R A B MUTE CLIP After completing "Setting up the speakers automatically (AUTO SETUP)", the most suitable equalizer curve for the frequency characteristics of your speakers and the room will be set for each ACTIVE EQ mode. 1 For the remote control unit, press the RCV MODE key to switch to receiver mode. 2 Press the ACTIVE EQ key for the following selections; 1 ACTIVE EQ OFF : The ACTIVE EQ function is turned OFF. 2 ACTIVE EQ FLAT* : Frequency response from speakers are flat. 3 ACTIVE EQ MUSIC : Effective when listening to music. 4 ACTIVE EQ CINEMA : Effective when watching movie. 5 ACTIVE EQ GAME : Effective when playing video game. *It can be selected after AUTO SETUP is carried out. SP L C LFE R A B MUTE CLIP STEREO SL S SB SR 1 Use the INPUT SELECTOR key or Input Selector keys to select the source of which the input level you want to adjust. • You can store a separate input level for each input source. 2 For the remote control unit, press the RCV MODE key to switch to receiver mode. 3 Press the SOUND key and 5/∞ keys or MULTI @/# keys repeatedly until the “INPUT” indication appears. 4 Use the MULTI CONTROL knob or MULTI %/fi keys to adjust the input level. SP L C LFE R A B MUTE CLIP STEREO SL S SB SR • ACTIVE EQ function will not be available when in REC mode. SL S SB SR • The adjustment mode is displayed for approximately 20 seconds. • The input level can be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 5 Press the SOUND key to accept the setting. 25 EN *5556/24-31/EN 25 05. 7. 6, 0:21 PM Normal playback Adjusting the TONE You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. 1 For the remote control unit, press the RCV MODE key to switch to receiver mode. 2 Press the TONE key to select the TONE mode. 3 Use the MULTI CONTROL knob or MULTI %/fi keys to select TONE ON/OFF. SP L C LFE R A B MUTE CLIP STEREO One-touch low frequency emphasis (BASS BOOST) You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo modes. • Press the key once to select the maximum (+10) low frequency emphasis setting. • This key does not function when the receiver is in the sound quality or ambience effects adjustment mode. • This function is available only for speakers connected to FRONT A terminals. Switching back to the previous setting Press the BASS BOOST key again. SL S SB SR 4 When in TONE ON selection, press the TONE key for the following displays. BASS : Select this to adjust the low frequency range. [. . . ] 87. 5 MHz ~ 108. 0 MHz Usable sensitivity MONO . . . . . . . . . . . . . . . . . . . 1. 3 µV (75 Ω)/ 13. 2 dBf (40 kHz dev, S/N 26 dB) STEREO . . . . . . . . . . . . 45 µV (75 Ω)/ 42. 1 dBf (40 + 6 kHz dev, S/N 46 dB) Total harmonic distortion MONO (1 kHz, 40 kHz dev) . . . . . . . . . . . . . . . . . . . . . . . 0. 2% (65. 2 dBf input) STEREO (1 kHz, 40 + 6 kHz dev) . . . . . . . . . . . . . . . [. . . ]