User manual KENWOOD KVT-512

[. . . ] Press the reset button. · If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. · If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with the same rating. · Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. [. . . ] · After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. · Mount the unit so that the mounting angle is 30° or less. · This unit has the cooling fan (page 5) to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction. 2WARNING · If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. Accessories 1 . . . . . . . . . . 1 2 . . . . . . . . . . 1 3 . . . . . . . . . . 2 4 . . . . . . . . . . 1 ¤ · Mounting and wiring this product requires skills and experience. For safety's sake, leave the mounting and wiring work to professionals. · Make sure to ground the unit to a negative 12V DC power supply. · Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Parking sensor wire (Light Green) PRK SW For the sake of safety, be sure to connect the parking sensor. Connect to vehicle's reverse lamp harness when using the optional rear view camera. Reverse sensor wire (Purple/White) To steering remote Steering remote control input (Light Blue/Yellow) To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. When this terminal is not in use, leave its cap on. Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Mute wire (Brown) Power control/ Motor antenna control wire (Blue/White) If no connections are made, do not let the cable come out from the tab. 4| KVT-522DVD/KVT-522DVDY/KVT-512 Cooling fan Antenna Cord Do not connect. Wiring harness (Accessory 1) FM/AM antenna input (JASO) Wiring harness (Accessory 2) AV IN REAR VIEW CAMERA Audio/Visual input / Rear View Camera Input · Visual input (Yellow) · Audio left input (White) · Audio right input (Red) Audio/Visual Output · Visual output (Yellow) · Audio left output (White) · Audio right output (Red) REVERSE AV OUT REMO. CONT REAR/SUB WOOFER Rear/Subwoofer Preout · Audio left output (White) · Audio right output (Red) MUTE FRONT Front Preout · Audio left output (White) · Audio right output (Red) ANT CONT P. CONT English | 5 Optional Accessory Connection iPod (commercially available) KCA-iP300V (Optional Accessory) Audio Input Resistance-free stereo type mini plug (3. 5) iPod AUDIO IN Audio Output (Black) Visual Input (Yellow) Resistance-free mini plug (3. 5) Visual Output (Yellow) USB terminal USB terminal KCA-BT200 input (Optional Accessory) Connection cable (Included in the Navigation System) TV Tuner (Optional Accessory) TV ANTENNA INPUT Navigation System (Optional Accessory) 6| KVT-522DVD/KVT-522DVDY/KVT-512 TO MONITOR UNIT Connection cable (Included in the TV tuner) Installation/Removing the Unit Installation Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Metal mounting strap (commercially available) Make sure that the unit is installed securely in place. [. . . ] Self-tapping screw (commercially available) Metal mounting strap (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). English | 7 Installation/Removing the Unit Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 3 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Escutcheon (Accessory 4) Removal Tool (Accessory 3) Removing the Unit 1. [. . . ]