User manual KENWOOD KVT-647DVD

[. . . ] Connect the wiring harness wires in the following order: ground, battery, ignition. Connect the wiring harness connector to the unit. 2WARNING • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. [. . . ] € After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. € Mount the unit so that the mounting angle is 30° or less. 21 7:12:57 PM Connection Monitor unit For the sake of safety, be sure to connect the parking sensor. Accessory 3 Connect to the vehicle's parking brake detection switch harness using the supplied relay connector. Parking sensor wire (Green) PRK SW To vehicle's reverse lamp harness To car light control switch Reverse sensor wire (Pink) REVERSE Dimmer control wire (Orange/White) ILLUMI Steering remote control input To Steering remote (Light Blue/Yellow) Ignition key switch Car fuse box (Main fuse) Car fuse box ACC REMO. CONT A A B Ignition wire (Red) ACC B C Battery wire (Yellow) BATT (5A) Ground wire (Black) - (To car chassis) C + Receiver unit (front side) SUB R-CAM V-IN VIDEO L R PRE OUTPUT REAR L R FRONT L POWER R Accessory 4 Battery VIDEO FM /AM ANTENNA VIDEO AV OUTPUT AV INPUT 2 L AV INPUT 1 L R R L R Antenna cord FM/AM antenna input Accessory 1 C B Ground wire (Black) - (To car chassis) Battery wire (Yellow) (10A) Connect to the terminal that is grounded when either the Mute wire (Brown) telephone rings or during conversation. To connect the kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, connect either to the Motor antenna control wire (Blue) control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. When using the optional power amplifier, connect to its power Power control wire (Blue/White) control terminal. " terminal of the amplifier having the external External amplifier control wire (Pink/Black) amp control function. (Optional) Connection cable (Included in the disc changer) Receiver unit (rear side) Accessory 2 TV tuner (Optional) TV ANTENNA INPUT FRONT L White/Black White + Navigation System (Optional) To front left speaker FRONT R Gray/Black Gray + To front right speaker If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. rEAR L Green/Black Green + To rear left speaker REAR R Purple/Black Purple + To rear right speaker B54-4502-00_00_English. Indd 5 TO NAVIGATION I/F TO TV TUNER I/F TO MONITOR UNIT TO MONITOR I/F TO 5L I/F Connection cable (Included in the Navigation system) Connection cable (Included in the TV tuner) English | 5 06. 21 7:12:58 PM Connection for AV Equipments AV OUTPUT VIDEO FM /AM ANTENNA VIDEO AV INPUT 2 L AV INPUT 1 L R R L R-CAM V-IN VIDEO SUB L R PRE OUTPUT REAR L R FRONT L POWER R R ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■ Subwoofer Preout • Audio left output (White) • Audio right output (Red) ■ Rear View Camera Input • Visual input (Yellow) ■ Audio/Visual Output • Visual output (Yellow) • Audio left output (White) • Audio right output (Red) ■ Audio/Visual input 1 (KVT-617DVD) Audio/Visual input (KVT-647DVD) • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Audio/Visual input 2 (KVT-617DVD only) • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) 6 | English B54-4502-00_00_English. 21 7:12:58 PM Installation for Monitor Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Metal mounting strap (commercially available) Accessory 5 Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Attach the installation brackets 9 to the sides of the hideaway unit using the sems bolts 7. installation brackets (Accessory 9) Sems bolts (M4 × 8 mm) (Accessory 7) 2. [. . . ] If so, tighten the bracket using accessories 0 as shown below. Use accessories 0 at both sides as shown. accessory 0 Audio unit or others 2. (M5x6mm) Screws (included in audio unit package) Screws (included in audio unit package) 10 | English B54-4502-00_00_English. [. . . ]