User manual KENWOOD LZ-701W

[. . . ] . 8 Remote Control Function <Provided with the KTC-V800N/V800P> . Installation for the Video Box Unit Connection . . 10 . 10 . 11 . 14 . 15 Troubleshooting Guide . 17 The control screens shown in this manual are for explanation purposes only. [. . . ] The [ TINT ] and [ COLOR ] cannot be adjusted for the navigation picture. [BRIGHTNESS] and [DIMMER] initial values are maximum. As regards [DIMMER] adjustment: When the condition is bright around the periphery of the monitor unit, the brightness does not change even when [DIMMER] is adjusted. When set to maximum, even if the monitor unit periphery dims, there is no change in from the brightness set with [BRIGHTNESS]. There is no connection with the vehicle's illumination switch. (A sensor is installed facing the front of monitor unit for light detection). If you make no key operation for 10 seconds, the picture quality adjustment screen is automatically cancelled. 5 Operation English 7. 0-inch WIDE COLOR LCD MONITOR V. SEL MODE SCRN Selecting the Channels <When the KTC-V800N or KTC-V800P is connected> Auto Seek Mode (AUTO1) Press the [ 3 ] button to seek for channels up the band. Press the [ 2 ] button to seek for channels down the band. Preset Station Seek Mode (AUTO2) Press the [ 3 ] button to move to the next preset station. Press the [ 2 ] button to move to the last preset station. Manual Seek Mode (MANU) Press the [ 3 ] button to increase the channel by one step. Press the [ 2 ] button to decrease the channel by one step. Setting the Function 1 Press the SCRN button for at least two second, the function setting screen to be displayed. 2 Each time you press the SCRN button, the setting item can be selected. 3 Press the [ 2 ] or [ 3 ] button to set the function. Selecting the Preset Bands [TV BAND] <When the KTC-V800N or KTC-V800P is connected> Press the [ 2 ] or [ 3 ] button to switch to the preset band TV1 and TV2. FUNCTION TV BAND TV2 SEEK MODE AUTO1 5 3 TV1 3 TV2 6 Selecting the Seek Mode [SEEK MODE] <When the KTC-V800N or KTC-V800P is connected> You can choose from three seek modes: auto seek, preset station seek, and manual seek. Press the [ 2 ] or [ 3 ] button, the mode switches as follows: [AUTO 1]: Auto Seek Mode 5 5 FUNCTION TV BAND TV2 SEEK MODE AUTO1 5 AUTO1 33 AUTO2 MANU [AUTO 2]: Preset Station Seek Mode [MANU]: Manual Seek Mode Channel Preset Memory [USER PRESET MEMORY] <When the KTC-V800N or KTC-V800P is connected> Store the channel of the station currently being looked to. FUNCTION 5 USER PRESET MEMORY 3 P1 P5 2 7 P2 P6 3 9 3 P3 4 P4 6 1 Press the [ 2 ] or [ 3 ] button to select the [ P1 ] [ P8 ]. 2 Press the SCRN button for at least two seconds to store the channel of the station currently. NOTE P7 10 P8 12 You can store 8 stations in each of the TV1 and TV2 preset bands. Selecting the Reception Area [TV AREA] <When the KTC-V800P is connected> Press the [ 2 ] or [ 3 ] button to select the channel setting for your country as follows: FUNCTION TV AREA TV1 1 2 China Singapore Malaysia Thailand Brunei Hong Kong Indonesia Australia PAL-D 1 3 2 3 3 4 5 China PAL-B/G 3 4 5 NOTE PAL-I PAL-B/G The reception area can be set for two separate preset bands, TV1 and TV2. 7 Operation English 7. 0-inch WIDE COLOR LCD MONITOR V. SEL MODE SCRN Setting the Remote Sensor On/Off [REMOTE] If this unit also runs when operating other units with different Kenwood remote controls, its remote control function can be turned off. Press the [ 2 ] or [ 3 ] button to switch the function on and off. FM Transmitter Function [FM-TX] <When the KTC-V800N* or KTC-V800P is connected> You can use the FM transmitter function to hear the sound of the TV, video from your car FM radio. Press the [ 2 ] or [ 3 ] button to change the frequency by 0. 1 MHz step and off [OFF]. NOTE FUNCTION REMOTE FM-TX AV-OUT OFF 87. 5MHz NORMAL ON 3 3 OFF FUNCTION REMOTE FM-TX AV-OUT OFF 87. 5MHz NORMAL *The KTC-V800N is not display the FM transmitter function depending on the sales area. Be sure to select a frequency that is not the same as a broadcast station in your area. The auto seek function on your car radio may not stop at the FM transmitter frequency. In this case, use the manual seek function to set the radio to the FM transmitter frequency. 3 87. 5 3 Switching the AV Output [AV-OUT] <When the KTC-V800N or KTC-V800P is connected> Press the [ 2 ] or [ 3 ] button, the AV output mode switches as follows: FUNCTION REMOTE FM-TX AV-OUT 3 TV OFF 87. 5MHz VIDEO1 3 VD1 [NORMAL](NOR): Picture/sound with monitor picture [TV]: Television picture/sound NOR VD2 [VIDEO1](VD1): Video 1 picture/sound [VIDEO2](VD2): Video 2 picture/sound 8 Remote Control Function <Provided with the KTC-V800N/KTC-V800P> 2CAUTION Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries 1. Use two "AA" batteries: Slide the cover while pressing downwards to remove it as illustrated. Insert the batteries with the and poles aligned properly following the illustration inside the case. 2WARNING Store unused batteries out of the reach of children. [. . . ] Engaging the parking brake will cause picture to be displayed. If the temperature of the monitor unit drops, the screen may appear darker when power is first turned on due to the characteristics of a liquid crystal panel. Wait a while after turning power on for the temperature to rise. Separate the two antennas as far as possible. [. . . ]