User manual KENWOOD TH-F7E

[. . . ] INSTRUCTION MANUAL FM TRIBANDER TH-F6 144/ 220/ 440 MHz FM TRIBANDER TH-F6A TH-F7E 144/ 430 MHz FM DUAL BANDER KENWOOD CORPORATION B62-1441-00 (K, E, T) 09 08 07 06 05 04 03 02 01 00 MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual. TH-F6A: TH-F7E: 144/ 220/ 440 MHz FM Tri-band Portable Transceiver 144/ 430 MHz FM Dual-band Portable Transceiver NOTICE TO THE USER One or more of the following statements may be applicable for this equipment. FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. MARKET CODES K-type: E-type: T-type: The Americas Europe/ General The United Kingdom INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] To quit the function, press [ ] or [PTT]. When a CTCSS frequency is identified, the identified frequency appears and blinks. 2 Press [ ] or [MNU] to program the identified frequency in place of the current CTCSS frequency. Otherwise, press [ ] if you do not want to program the identified frequency. Turn the Tuning control or press [ ]/ [ ] while the identified frequency is blinking to resume scanning. When the DCS function is ON, you will hear calls only when the selected DCS code is received. To answer the call, press and hold the PTT switch, then speak into the microphone. Note: You cannot use the DCS function and CTCSS/ Tone functions simultaneously. Switching the DCS function ON after having activated the CTCSS/ Tone functions deactivate the CTCSS/ Tone functions. Available CTCSS frequencies No. (Hz) 67. 0 69. 3 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 91. 5 94. 8 No. (Hz) 97. 4 100. 0 103. 5 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 131. 8 136. 5 No. (Hz) 141. 3 146. 2 151. 4 156. 7 162. 2 167. 9 173. 8 179. 9 186. 2 192. 8 203. 5 No. (Hz) 206. 5 210. 7 218. 1 225. 7 229. 1 233. 6 241. 8 250. 3 254. 1 SELECTING A DCS CODE 1 While in DCS mode {above}, press [F], [TONE]. The current DCS code appears. 2 Turn the Tuning control or press [ ]/ [ ] to select your desired DCS code. The available DCS codes are shown in the following table. 023 025 026 031 032 036 043 047 051 053 054 065 071 072 073 074 114 115 116 122 125 131 132 134 143 145 152 155 156 162 165 172 174 205 212 223 225 226 243 244 245 246 251 252 255 261 263 265 266 271 274 306 311 315 325 331 332 343 346 351 356 364 365 371 411 412 413 423 431 432 445 446 452 454 455 462 464 465 466 503 506 516 523 526 532 546 565 606 612 624 627 631 632 654 662 664 703 712 723 731 732 734 743 754 Note: x Received signals are monitored through the speaker while scanning is in progress. ID Scan does not scan the tone if a signal is not detected. x If the CTCSS function is activated for both the A and B-band, the scan speed may be slower. 3 Press [ ] or [MNU] to store the new setting. Otherwise, press [ ] or [PTT] to cancel. 29 8 SELECTIVE CALL DCS CODE ID SCAN This function scans through all DCS codes to identify the incoming DCS code on the received signal. You may find this useful when you cannot recall the DCS code that the other persons in your group are using. 1 While in DCS mode, press [F], [TONE] (1 s) to start the DCS Code ID Scan function. To reverse the scan direction, turn the Tuning control or press [ ]/ [ ]. To quit the function, press [ ] or [PTT]. When a DCS code is identified, the identified code appears and blinks. 2 Press [ ] or [MNU] to program the identified frequency in place of the current DCS code. Otherwise, press [ ] if you do not want to program the identified code. Turn the Tuning control or press [ ]/ [ ] while the identified DCS code is blinking to resume scanning. Note: x Received signals are monitored through the speaker while scanning is in progress. x DCS Code ID Scan does not scan the code if a signal is not detected. [. . . ] 26 Simplex Storing, Frequencies or Standard Repeater Frequencies. . . . . . . . . . . . 15 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 53, 54 Squelch, Adjusting . . . . . . . . . . . . . . . . . . . . . . . . 6 Supplied Accessories . . . . . . . . . . . . . . . . . . . . . [. . . ]